Kiturami KRPB-20A Installation & Operation Instructions Download

Page: 26 / 33

The actual product may differ from
the images in the manual.

- 26 -

ERROR CODE LIST & TROUBLESHOOTING

ERROR

CODE

ERROR CODE DESCRIPTION

CHECKLIST

Not detecting flame normally

Broken Photocell sensor

Not enough fuel in the tank

Supplied electricity, but heater not working

Check heater for short

(infinity resistance means short)

Broken load detector for heater

Clogged fuel in feeding pipe

(Limit switch on feeding pipe activated)

Excessive fuel supply (adjust the fuel supply)

Fuel not supplied due to excessively low fuel hose

Broken limit switch on feeding pipe

Water temperature sensor not reading

temperature measurements

Defectiv e or broken water temperature sensor

Not reading the blower RPM

Defectiv e or broken blower connection

Blower RPM out of range

Clogged tubes or flue

Poor communication with room thermostat

Defectiv e or broken connection with room thermostat

Not detecting flame after ignition

Clogged tubes or flue

Improper cleaning of ash cleaner

Not sensing low water level in the heat

exchanger

Defectiv e earth connection (black color) or

low water lev el sensor

Sensor sensing more than 91

water

℃

temperature

Defectiv e circulation pump operation or poor plumbing

Activation of ov er heating bimetal on burner

parts

Poor sealing of fuel parts and defective burner

Summary of Contents for KRPB-20A


































Search results

Summary of Contents for KRPB-20A

Reviews:

Related manuals for KRPB-20A

Brands by name

Popular brands

Kiturami KRPB-20A, Installation & Operation Instructions

Search results

Summary of Contents for KRPB-20A

Reviews:

Related manuals for KRPB-20A

Brands by name

Popular brands