background image

The  actual  product  may  differ  from 
the  images  in  the  manual.                                             

-  20  -

Room  Control  -  Bath  Function

For  the  boiler  for  both  hot  water  and  heating

※ 

Using  the  bath  function

■ 

1)  To  use  lots  of  hot  water,  select  bath  by 

  using  the  bath  button.

2)  2  1/2  hours  after  selecting  the  bath 

  function,  it  returns  to  the  previous  function.

3)  If  the  line  water  pressure  is  above 

  196Kpa  (2kgf/ ),  install  a  pressure-reducing  valve.

What  is  the  temperature  setting  function?

■ 

  1)  It  sets  the  output  water  temperature

  in  the  Room,  Reservation,  and  Outing

  functions;  configure  the  desired  temperature

  in  the  bath  function  as  the  set  temperature.

Setting  the  hot  water  temperature

■ 

  1)  Select  the  Bath  function  by  using  the  bath  function  button.

  2)  Select  the  temperature  by  pressing  the  up( )  /  down( )  button.

  3)  In  the  temperature  setting  function,  the  range  of  temperature  is  35~60

.

Cautions  while  using  the  Bath  function.

☞ 

 

Take  care  against  burns  caused  by  the  hot  water.

• 

 

Take  care  when  opening  the  water  tap  after  setting  the  bath 

• 

  function,  since  hot  water  may  come  out  suddenly.

 

Extra  caution  is  required  so  that  the  sick  and  aged  and  children  are 

• 

  not  burned  by  the  hot  water.

 

The  water  from  the  boiler  is  not  potable.

• 

 

During  heating  (indoor  operation),  after  hot  water  is  used  for  a  long  time, 

• 

  lukewarm  water  may  come  out.

 

During  the  bath  function,  if  power  is  turned  off  and  on,  it  will  return  to 

• 

  the  pre-bath  function.

Summary of Contents for KRPB-20A


































Reviews: