manualshive.com logo in svg

KitchenAid KBFA20ER, Technical Education

Share
Download
KitchenAid KBFA20ER Technical Education Download Page 45

4-23

REMOVING THE FRONT AND REAR ROLLERS

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before    
operating.
Failure to do so can result in death or 
electrical shock.

1.  Unplug refrigerator or disconnect power.
2.  Pull the refrigerator away from the wall.
3.  Unsnap and remove the air grille from the 

refrigerator.

4.  Pull the front roller cover off the roller you 

are removing.

5. 

To remove a front roller:

a) Tilt the refrigerator back approximately 

3

˝

 and prop the front up.

b) Turn  the  silver  (outer)  leveling  screw 

to  the  left  (counterclockwise)  and  re-
move the threaded end from the front 
roller.

  Air Grille

  Front Roller Cover

c)  Rotate the front roller so that the brack-

et tab aligns with the chassis slot, and 
remove the roller.

  Front Roller

  Bracket 

 Tab In Slot

  Front Roller Leveling Screw

6. 

To remove a rear roller:

a) Tape the refrigerator doors closed.
b) Tilt  the  refrigerator  forward  approxi-

mately 4

˝

 and prop the back up.

Continued on the next page.

Summary of Contents for KBFA20ER





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands