manualshive.com logo in svg

KitchenAid KBFA20ER, Technical Education

Share
Download
KitchenAid KBFA20ER Technical Education Download Page 36

4-14

REMOVING THE EVAPORATOR FAN MOTOR, DEFROST 

BIMETAL, DEFROST HEATER, & EVAPORATOR

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before    
operating.
Failure to do so can result in death or 
electrical shock.

1.  Unplug refrigerator or disconnect power.
2.  Open  the  freezer  compartment  and  re-

move all of the items inside the compart-
ment.

 Evap Fan Motor, Defrost 

Bimetal, Defrost Heater, 

& Evaporator

3.  Remove the freezer thermistor (see page 

4-12 for the procedure).

4.  Remove  the  freezer  basket  and  left  and 

right  freezer  basket  glides.  Press  the  re-
lease lever to remove the glides.

6.  Remove the three hex-head screws from 

the left glide support and remove the sup-
port.

 Left Glide Support Screws

5.  Press  the  release  arm  on  the  left  freezer 

basket  glide,  and  pull  the  glide  out  of  its 
support.

 Left Glide Release Arm

7.  Press a screwdriver blade against the left, 

right,  and  then  center  air  diffuser  release 
tabs, and pull the diffuser off the evaporator 
cover.

 3 Air Diffuser Release Tabs

8.  Press  the  locking  tabs  to  release  the  ice 

maker power connector, and push the con-
nector inside the evaporator cover opening.

 Ice Maker Connector

Summary of Contents for KBFA20ER





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands