manualshive.com logo in svg

KitchenAid KBFA20ER, Technical Education

Share
Download
KitchenAid KBFA20ER Technical Education Download Page 39

4-17

REMOVING THE DUAL WATER VALVE

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before    
operating.
Failure to do so can result in death or 
electrical shock.

1.  Unplug refrigerator or disconnect power.
2.  Turn off the water supply to the refrigera-

tor.

3.  Pull the refrigerator away from the wall so 

that you can access the rear of the unit.

4.  Disconnect the water line from its fitting.
5.  Remove the four hex-head screws from 

the water valve access cover, but do not 
remove the cover at this time.

Water Valve Access Cover

 Cover Screw  

 (1 of 4)

 Water Line Fitting

 Water Line 

 Fitting Retainer 

 Fitting Bracket

6.  Squeeze  the  sides  of  the  water  line  fit-

ting retainer and slide the retainer off its 
bracket.

 Slide Fitting   

 Off Retainer

7.  Slide the water line fitting off the retainer.

Continued on the next page.

Summary of Contents for KBFA20ER





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands