CONFIGURATION MODE
This document contains confidential information. Dissemination, publication, copying, or duplication of this document or software described herein without prior written authorization is strictly prohibited.
kitchenbrains.com
Page 11 of 16
© 2020 Kitchen Brains
THE TWO RELAY MODES ARE:
Unlatched –
Default Setting. Relay activates when alarm
occurs and deactivates when Silence is pressed. Typical
Application: Controlling a remote buzzer or light.
1. Press gear button to access menu
2. Scroll to unlatched relay mode
3. Select unlatched
75LCT MULTI-MONITOR |
OPERATING MANUAL
Latched –
Relay activates when alarm occurs and
deactivates when both alarm condition has been cleared and
Silence has been pressed. Typical Application: Connection to
a building management system where relay remains activated
until alarm condition clears and is acknowledged.
1. Press gear button to access menu
2. Scroll to latched relay mode
3. Select latched
INSTALLATION GENERAL SAFETY MEASURES AND PRODUCT LIMITATIONS
• This product (“Product”) must be installed by a licensed electrician
experienced in working in the types of environments for which this
Product is intended to be utilized; specifically, commercial Cooler/
Freezer coolers and freezers (“Equipment”).
• Personnel installing the Product must carefully and completely
read the Operating and Installation Instructions (“Instructions”),
and instructions and specifications of the Equipment manufacturers,
before attempting to operate and install the Product. Failure
to comply with the Instructions, and the instructions and
specifications of the Equipment manufacturers, may result in
personal injury and/or property damage and may void the
warranty of the Product. Retain the Instructions for
future reference.
• The Product shall only be used for the purposes described in
the Instructions.
• During installation of the Product, all applicable laws, regulations
and industry rules, including local electrical and safety codes, the
National Electric Code (NEC) and the Occupational Safety and
Health Act (OSHA), must be strictly followed. Consistent
therewith, follow applicable electrical codes regarding running of low
voltage wiring and high voltage wiring in separate conduits and use
appropriately rated wire (insulation type, voltage rating and wire
gauge) for all connections. Supply connection wiring must be rated
at least 90°C. Use copper conductors only.
• The enclosure used for mounting the Product must be properly
grounded according to electrical code.
• Confirm that the power source conforms to the requirements of the
Product before connecting.
• Do not exceed the rated limits of the Product. Refer to the Product
specifications for suitability of the Product to the application.
• The Product is not suitable for use in wet locations. Do not expose
the Product to water, moisture or condensation. In no event should
the Product be exposed to environments where sudden
temperature changes with high humidity may result in the
formation of condensation.
• Any openings in the walls, ceiling or floor of the Equipment
for wiring or other reason must be sealed (made airtight and
watertight) with appropriate materials (e.g., silicone, caulk or
foam), both on the outside and inside of the Equipment, to prevent
moisture or condensation from entering the compartment of the
Equipment and forming and accumulating on the interior walls of
the compartment and the contents of the compartment, including
the Product. Failure to properly seal such openings may (i) result
in damage to the Equipment and contents of the compartment
(ii) pose a safety hazard and (iii) void the warranty of the Product.
• To prevent moisture or condensation from entering or forming
in the enclosure used for the Product, any openings in this
enclosure (for wiring access or other purpose) must be
appropriately sealed with materials such as silicone, caulk
or foam.
• Installation of the Product should be inspected and the Product
tested by qualified personnel to ensure the Product performs
safely and in accordance with the Product specifications.
Periodic testing of the Product should be performed on an
ongoing basis (at least quarterly) to ensure the Product
continues to perform properly.
• All personnel operating, maintaining, repairing or interfacing with
the Product must be instructed in the use of the Product and
provided with the Instructions. The Instructions must be kept in an
accessible location for easy reference.
•
WARNING:
Hazard of electric shock! Power sources must be
turned off or otherwise disconnected prior to installation or
servicing of the Product. Lock and tag power disconnects to
prevent an unexpected application of power.
