Kitagawa TT200BE-01 Instruction Manual Download

Page: 35 / 69

NOTICE

11-3. Backlash adjusting method of rotating axis worm gear (See Fig.8)

）

Drain lubrication oil from the rotating axis lubrication oil drain port. (See the outside view.)

）

Remove the cover

①

）

Remove hexagon socket head cap screw

③

and washer

④

which fix lock nut

②

）

The lock nut

②

is engaged with the bearing case

⑤

by M42, P1.5 screw. Since eight 5mm drill

holes are provided on the periphery of the lock nut

②

and the bearing case

⑤

, fix the bearing case

⑤

with a proper round bar before loosening the lock nut

②

）

When rotating and advancing the bearing case

⑤

clockwise by using the above 5mm drill hole, the

backlash becomes small.

）

After adjusting the backlash, fix the bearing case

⑤

and tighten the lock nut

②

securely. Then,

measure the backlash again and check that it is proper.

）

After checking that the backlash is proper, mount the cover

①

again to the original position with

hexagon socket head cap screws

③

and washer

④

Each interval between the hole and the hole of periphery of bearing case

is 45

. When rotating the bearing case 45

, the backlash of about

μm is reduced at arc length on the peripheral position of table.

Adjust the backlash slowly and carefully without adjusting the backlash

at a time.

When mounting the cover

①

, do not damage O-ring

⑥

Bearing case

⑤

5mm drill

Cross section A-A

Hex. socket head

cap screw

③

Washer

④

Cover

①

Bearing case

⑤

O-ring

⑥

Lock nut

②

CAUTION

M42

1.5

Fig.8

Summary of Contents for TT200BE-01






































































Search results

Summary of Contents for TT200BE-01

Reviews:

Related manuals for TT200BE-01

Brands by name

Popular brands

Kitagawa TT200BE-01, Instruction Manual

Search results

Summary of Contents for TT200BE-01

Reviews:

Related manuals for TT200BE-01

Brands by name

Popular brands