Kitagawa TT200BE-01 Instruction Manual Download

Page: 14 / 69

2. Outside view

The following figure is the standard outline drawing of model TT200. Since the table clamp device is

displayed without classifying the oil hydraulic pressure specification and the pneumatic specification in

the following figure, the oil hydraulic pressure supply port becomes valid only when the oil hydraulic

pressure system is used.

Thus, the air hydraulic booster is built-in only when the air hydraulic pressure system is used. For

detailed models, refer to attached outside view.

Motor case for
rotating axis

Connector plate

Cable

Silencer
(Air hyd. pressure unit)

Pneumatic supply port
(for air purge used by air hyd.,
or oil hyd. spec.)

Cover

Hyd. oil

supply port

for air hyd. unit

Oil gauge for air hyd.

Lub. oil supply port
for tilting axis

Oil gauge for
tilting axis (base)

Lub. oil drain port
for tilting axis

Oil gauge for rotating axis

Lub. oil drain port for rotating axis

Lub. oil supply port for rotating axis

Connector plate

Cable

Cover

Screws for eye bolts (hoist)

Table

Screw for eye bolt (hoist)

Hydraulic  port  for
tilting  axis  clamp
(in hyd. spec.)

Hydraulic port for
rotating axis clamp
(in hyd. spec.)

Lub. oil supply port
(gear box)
Lub. oil drain port
(gear box)

Motor case for tilting axis

M5 tap for exhaust
port for air purge

Cover

Name plate

Summary of Contents for TT200BE-01






































































Search results

Summary of Contents for TT200BE-01

Reviews:

Related manuals for TT200BE-01

Brands by name

Popular brands

Kitagawa TT200BE-01, Instruction Manual

Search results

Summary of Contents for TT200BE-01

Reviews:

Related manuals for TT200BE-01

Brands by name

Popular brands