Kitagawa TT200BE-01 Instruction Manual Download

Page: 47 / 69

17. Connector

When removing connectors (made by MOLEX) such as proximity switches, etc., unavoidably in motor

case removing, the following procedure is recommended.

17-1. To remove connector

1) Pushing the claw

③

of receptacle housing, remove the plug housing

①

and receptacle housing

②

Do not apply any load to cables.

17-2. To mount connector

1) Mate the plug housing

①

to the receptacle housing

②

as shown in the following figure.

2) Insert the receptacle housing

②

into the plug housing

①

securely until a clicking noise occurs.

3) After mounting, pull the receptacle housing

②

slightly and check that it does not draw out.

Check that connectors and cables are not damaged before connecting.

Connect cables so as not to be bent or crushed.

Do not apply any load to cables.

Receptacle housing

②

Plug housing

①

Claw

③

Plug housing

①

Receptacle housing

②

CAUTION

Fig.18

Fig.19

Summary of Contents for TT200BE-01






































































Search results

Summary of Contents for TT200BE-01

Reviews:

Related manuals for TT200BE-01

Brands by name

Popular brands

Kitagawa TT200BE-01, Instruction Manual

Search results

Summary of Contents for TT200BE-01

Reviews:

Related manuals for TT200BE-01

Brands by name

Popular brands