manualshive.com logo in svg

KISANKRAFT KK-CSP-5720, User Manual, Page: 9 / 52

Share
Download
KISANKRAFT KK-CSP-5720 User Manual Download Page 9

KisanKraft

®

 

HEAVY DUTY Petrol Chainsaw  

KK-CSP-5720-8650

 

 

: www.kisankraft.com 

: [email protected] 

: +91.80. 22178200 

 

Page 9 of 52 

IMPORTANT 

If warning seals peel off or become soiled and is impossible to read, you should contact the 
dealer from which you purchased the product to order new seals and affix the new seal(s) in the 
required location(s). 

Symbols on the Machine: 

For  safe  operation  and  maintenance,  symbols  are  carved  on  the  machine.  Follow  these 
indications and please be careful not to make any mistake. 

The port to refuel the“ MIX PETROL” 

 

The port to refuel the “CHAIN OIL” 

 

The indication regarding the choke. Pulling out the choke knob, the 
choke closes. 

 

The indication regarding the switch. Flipping the engine switch to 
the “O” (OFF) direction, the engine stops. 

 

The indication regarding the chain oil adjuster nut. 

“-” direction-the oil flow decrease 
“+” direction-the oil flow increase. 

 

H: The High-speed adjustment screw. 
L: The Slow-speed adjustment screw. 

 

Summary of Contents for KK-CSP-5720





















































Reviews:

No comments