manualshive.com logo in svg

KISANKRAFT KK-CSP-5720, User Manual, Page: 21 / 52

Share
Download
KISANKRAFT KK-CSP-5720 User Manual Download Page 21

KisanKraft

®

 

HEAVY DUTY Petrol Chainsaw  

KK-CSP-5720-8650

 

 

: www.kisankraft.com 

: [email protected] 

: +91.80. 22178200 

 

Page 21 of 52 

NOTE 

When restarting immediately after stopping the engine, leave the choke knob at the open 
position. 

 

WARNING 

Do not start the engine while holding the chainsaw with hand. The saw chain may touch your 
body and is very dangerous. 

Winter Use 

The intermediate wall is designed so it can 
be adjusted for running in cold weather, so 
that preheated air from the cylinder can 
pass into the carburetor space preventing 
icing of the air filter, etc.  

 

Break 

1. 

Don’t accelerate abruptly due to bad lubrication of the engine at the beginning of 
start-up. 

2. 

Avoid the speedy idle motion and over speed motion. If the engine runs at high 
speeds, it not only shortens the life of the engine but also causes more problems in 
the engine. 

Stopping the Engine 

1. 

Release the throttle lever to allow the engine to idle. 

2. 

Set the switch to the 

“OFF “position. 

SAWING

 

 

WARNING 

 

Before proceeding to your job, read 

“Safety Precautions” section it is recommended 

to first practice sawing easy logs. This also helps you get accustomed to your unit. 

 

Always follow the safety regulations. The chain saw must only be use for cutting 
wood. It is forbidden to cut other types of material. Vibrations are not recommended. 
do not use the chain saw as a lever for lifting moving or splitting objects .Do not lock 
it over fixed stands ,it is forbidden to hitch tools or applications to the p.t.o that are 
not specified by the manufacturer. 

 

It is not necessary to force the saw into the cut. Apply only light pressure while 
running the engine at full throttle. 

 

When the saw chain is caught in the cut, do not attempt to pull it out by force, but 
use a wedge or a lever to open the way. 

Summary of Contents for KK-CSP-5720





















































Reviews:

No comments