manualshive.com logo in svg

Kirby Morgan 525-769, Installation Manual

Share
Download
Kirby Morgan 525-769 Installation Manual Download Page 30

30

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210607001

Oral Nasal Mask and Microphone Installation

 

455 Balanced Regulator Installation

1.2.5 Oral Nasal Mask and 

Microphone Installation

1. Snap the oral nasal over the regulator mount 
nut. Take extra care to make sure the mask has 
snapped into position all the way around the 
mount nut.

2. Reinstall the communications module.

1.2.6 Nose Block Device Installation

1. Prior to reassembly, lubricate the two O-rings.

2. Slide the shaft through oral nasal mask in the 
helmet or mask shell.

3. Place both O-rings on the shaft, followed by 
the packing nut and the knob.

4. Tighten the knob with the pliers, padded by a 
cloth, while holding the nose pad end inside the 
helmet with your hand.

5. Tighten the packing nut with the 

7/16

 inch 

wrench until snug. Do not over tighten, as this will 
make it difficult to slide the nose block device in 
and out.

1.2.7 Chin Strap Replacement

NOTE

The adjustment strap should pull toward the 
right side of the helmet when it is on your 
head.

1. Put Loctite

®

 248 on the screws that secure the 

tabs that hold the chin strap.

2. Install the two screws that hold the chin strap 
in position, using the two screws supplied with 
the chin strap replacement kit. 

3. Tighten the screws with a torque screwdriver 
in accordance to the correct torque specification. 

ALWAYS REFERENCE

 Appendix Contents, 

Torque Specs starting on page APNDX-19 in the 
modular manual to confirm correct torque.

Summary of Contents for 525-769

































Reviews:

No comments

Brands by name

Popular brands

Load more brands