manualshive.com logo in svg

Kirby Morgan 525-769, Installation Manual

Share
Download
Kirby Morgan 525-769 Installation Manual Download Page 12

12

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210607001

Bent Tube Removal

 

SuperFlow® 350 Regulator Removal

Installing the 455 Balanced Regulator onto a  

SL 17C, SL 27

®

, KM 37 or KM 57 Helmet

Parts Included in the 525-765 Kit:

Part #

Description

Qty

100-100

Warranty Card

1

100-204

Installation Guide, 455 Regulator Kit

1

505-455

455 Balanced Regulator

1

520-042

Tie Wrap

2

VIDEO

How To: Conversion Kit, 
455 Regulator for KM 37, 
KM 57, SL 17C or SL 27

®

 

Helmet

https://www.youtube.com/
watch?v=qCucRRcp1fo

1.1 SuperFlow

®

 350 Regulator 

Removal

Tools Required:

•  Socket Wrench

•  1 

3/8

" inch socket and/or P/N 525-

625 Regulator Mount Socket Wrench 
(Found in 525-620 Tool Kit)

• 

3/8

" Drive Extension—Minimum 3" in Length

•   #1 Phillips Head Screwdriver

•  Open-End Wrench 

7/16

" and (2) 

7/8

" and 

11/16

" 

•  Slip Joint Pliers and a Cloth 

1.1.1 Bent Tube Removal

1. Always start removal at the side block end. 
Loosen the tube with the 

11/16

 inch wrench. The 

free swiveling mount nut on this end of the bent 
tube can be un-threaded completely and can 
slide down the tube.

Always start removal at the side block end.

2. Loosen the lower bent tube nut by using the 
two 

7/8

 inch wrenches. Place one wrench on the 

bent tube mount nut and the second on the 
regulator inlet jam nut. 

Turn only the outer nut 

on the bent tube to loosen the bent tube.

3. With the two mount nuts free; the bent tube 
assembly can be pulled straight out and away 
from the regulator. The bent tube assembly 
can be rotated back and forth to aid removal, if 
necessary.

Summary of Contents for 525-769

































Reviews:

No comments

Brands by name

Popular brands

Load more brands