manualshive.com logo in svg

Kirby Morgan 525-769, Installation Manual

Share
Download
Kirby Morgan 525-769 Installation Manual Download Page 24

24

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210607001

Nose Block Device Installation

 

REX® Pod System and Regulator Removal

3. Remove the screws that secure the whisker 
to the port retainer. Take care not to lose the 
whisker spacers and the zinc anodes. If the 
helmet has no anodes (standard on stainless steel 
helmets since late 2012) it will have kidney plates 
on the whiskers.

4. Remove the bent tube assembly as per "1.4.1 
Removal of the Bent Tube Assembly" on page 
BNT-6.

5. Remove the nose block device as per "1.2.1 
Nose Block Assembly Removal" on page FCPRT-6.

6. Remove the communication module from the 
helmet per "1.3.3 Removal of Communications 
Assembly" on page COM-3.

7. Remove the oral nasal mask by pulling it off the 
regulator mount nut.

NOTE

That the bottom two nuts attach on the 
exterior of the pod, while the remaining nuts 
attach on the interior of the pod.

8. Loosen the screws that secure the pod to the 
helmet shell gradually in a staggered pattern. This 
is much easier to do if you loosen the regulator 
mount nut so that the regulator is free to turn 
and allows access to the mounting screws.

Loosen the regulator for easier 

removal of the pod screw.

Summary of Contents for 525-769

































Reviews:

No comments

Brands by name

Popular brands

Load more brands