manualshive.com logo in svg

Kirby Morgan 525-769, Installation Manual

Share
Download
Kirby Morgan 525-769 Installation Manual Download Page 1

K

irby

 M

organ

®

455 Balanced Regulator Installation Guide

KMDSI Part #100-204

Patented, patents pending, foreign patents apply

TM

Kirby Morgan Dive Systems, Inc.

1430 Jason Way

Santa Maria, CA 93455, USA

Telephone (805) 928-7772, FAX (805) 928-0342

E-Mail: [email protected], Web Site:www.KirbyMorgan.com

B

 

WARNING

Diving with compressed breathing gas is a hazardous activity. Even if you do every-

thing properly there is always the danger that you may be killed or injured. No piece of 

diving equipment can prevent the possibility that you may be killed or injured any time 

you enter the water.

The 455 balanced regulator meets or exceeds all performance and testing requirements of all gov-
ernment and non-government testing agencies throughout the world. Only Kirby Morgan masks and 
helmets have achieved the Dive Lab

®

, CR (Commercial Rated) mark.

Kirby Morgan, SuperLite

®

, BandMask, Band Mask, KMB, KMB-Band Mask, DSI, Diving Systems Internation-

al, EXO, REX

®

, SuperFlow

®

 and DECA are all registered trademarks of Kirby Morgan Dive Systems, Inc. 

Use of these terms to describe products that are not manufactured by KMDSI is illegal.

The two dimensional images (such as photographs and illustrations) of our products are © copyright-
ed and trademarks of Kirby Morgan Dive Systems, Inc. The three dimensional forms of our products are 
trademark, trade design and trade dress protected.

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. This manual is made available for the ex-
press use of the owner of this Kirby Morgan product. No part of this manual may be reproduced, stored 
in any retrieval system, or transmitted, or used in any form or by any means, whether graphic, electronic, 
mechanical, photocopy, or otherwise by technology known or unknown, without the prior written per-
mission of Kirby Morgan Dive Systems, Inc.

Summary of Contents for 525-769

































Reviews:

No comments

Brands by name

Popular brands

Load more brands