Kingsman HBZDV4740 Installation Instructions Manual Download

Page: 32 / 41

General Vent Installation Information

Installation Of Side Wall Venting

1. The minimum distance from the bottom of fireplace to centre of vent is 44.5 inch

(130 cm) (See Figure 1). Cut a hole through the wall allowing for a 11” x 11” (inside diame-

ter) in combustible walls for wall thimble or an 8” diameter hole in a non-COMBUSTIBLE

wall (See Figure 2).

2. Note clearance to combustible as stated on pages 7 & 8.
3. Select the approximate vent length, precise measurements are not needed as your flex

pipe can be expanded to twice its shipped length for ease of installation.

4. To install wall thimble centre over 11” x 11” (inch) framing from both sides of wall and

secure. Route flex vent pipe through wall thimble (See Figure 1).

5. Before joining pipes, apply a bead of high temperature sealant (Mill Pac) to end of pipe.

First attach the four inch (4”) flue pipe to the vent termination with sealant, and secure with

4 screws provided. At this time make sure the spacer springs are attached to the (4”) flex

pipe as required. Then attach the seven inch (7”) pipe by the same method.

6. Mount vent termination and seal to wall using caulking around the wall thimble to weather

proof. After installing the vent termination, double check to make sure the pipe extends

properly through wall thimble and into vent termination.

7. Before joining pipes to fireplace flue, apply a bead of high temperature sealant (Mill Pac) to

end of pipe. First attach the four inch (4”) flue pipe to fireplace with Mill Pac sealant to the

flue pipe and secure with 4 screws provided. At this time verify that the spacer springs are

attached properly to the (4”) flex pipe as required. Then attach the seven inch (7”) pipe by

the same method.

8. Support horizontal pipes every two (2) feet (61 cm) with metal strap bands. Re-check fire-

place to make sure it is levelled and properly positioned and secured.

9. Support vertical pipes to maintain a minimum of 1” or greater clearance to combustibles

with metal strapping bands.

10. If finishing the outside wall with vinyl or wood siding it is recommended that a Siding

Shield be installed, Part Number ZDVSSLR.

Note: Wall Thimble cover combustible wall up to 11” thick.
Note: Venting termination must not be recessed into wall or siding.

FIGURE 2

FRAMING DETAIL

11.0"

8" DIA

44.5" TO CENTERS
MINIMUM

THROUGH COMBUSTIBLE
WALL

THROUGH
NON-COMBUSTIBLE WALL

TOP OF ENCLOSURE

With insulation
sleeve

50.5”

43 1/16”

44.5”

2 1/2”

18.875”

0.500”

Gyprock facing

NOTE:

1/4” RISE PER

FOOT OF

HORIZONTAL

RUN

Louvered Unit Shown

RIGID OR HARD PIPE

When using Simpson Duravent, AmeriVent pipe, ICC Excel Direct, Metal Fab Sure-Seal DV and or
Selkirk Direct Temp a Duravent hardpipe adapter must be used (

part # ZDVDFA for fireplaces and

part # ZDVDKA for Stoves, Serenity and ZDV3624B

). Follow installation instructions provided by

Simpson Duravent/AmeriVent/Selkirk Direct Temp, ICC Excel Direct, Metal Fab Sure-Seal DV for
installation of pipe and adhere to the clearance to combustibles provided in this manual. Apply a bead of
Mill Pac high temp sealant to all joints of pipes, adapters and termination, when using Kingsman Flex(Z-
Flex)Venting venting and Simpson Duravent venting.

NOTE:

Increase framing depth by one inch when using hardpipe.

Flex Pipe Venting

Kingsman Flex pipe is shipped in unexpanded length. When installing pipe expand the lengths. Pipe can
be expanded to twice their lengths e.g. 4ft. to 8ft. Fully expand pipe and cut off excess.

Do not use more than 2 couplers to extend short pipes. Single sections are preferred in an installation
attaching at the fireplace and termination.

Place the spring spaces provided approximately every two feet to stabilize 4” flex in the center of 7” flex.
When forming bends place spring in bend or before and after. (See Fig. 1).
Horizontal runs require support metal straps every 2 feet. In off set installation support straps should be
used to stabilize pipe.

Expand 4” and 7” flex pipe to the point that the 7” protrudes approximately 2 to 3 inches past outer wall and
the 4” flex protrudes approximately 2 to 3 inches past the 7” flex. See Fig. 1. Attach the 4” pipe to the termi-
nation first and secure with sealant and four screws then attach the 7” flex to the termination with caulking
and four screws. Termination may then be moved back to the outer wall and attached to home screwing
into the framing. Silicone around termination to waterproof. If siding shield is going to be used attach this
using same attaching hole as the top of termination after termination has been caulked for water proofing.

Use Hi Temp Sealant

Apply a bead of mill pac high temp sealant to all joints and use four screws to secure each pipe at fire-
place, termination and any joint if joining any sections of pipe.

NOTE:

It is critical to the proper and safe operation of this

fireplace that on all connections the inner liner and the
outer casing are both caulked with liberal amounts of
sealant. Do not use any kind of tape or silicone other than
that recommended in this manual, Mill Pac Sealant

FRAMING DIMENSION
Combustible Wall

Cut a 11” hole through exterior wall and frame as

shown below.

Non combustible Wall

Cut or drill 8” or 204mm diameter hole.

OPTIONAL
CLAMPS

FIGURE 1

MAX. DISTANCE BETWEEN SPACERS 2 FEET
SPRING SPACERS

OPTIONAL
CLAMPS

SEAL WITH HIGH TEMP. SEALANT

This gas appliance is approved to be vented either through the side wall or vertically through the roof.

Only Kingsman Flex(Z-Flex)Venting Kits and components