background image

Page 9 of 23 

 
Easibath backrests do not as standard have suckers attached to them. These sit on top of the base 
mattress as standard, and the back of the backrest ‘hooks’ under the lip of the top panel of the 
Easibath tub end. 
 
Knee Rests are provided with suckers for attachment directly to the bath tub base. They must not be 
placed on any other material such as another mattress, the suckers will not secure the support 
properly / safely. 

 
 
 
 

The Bathing Process 

 
Before  using  the  bath  /  the  bather  getting  into  the  bath,  the  water  should  be  turned  on  as  described 
below and allowed to flow into the bath with the pop-up waste(s) open to allow any cold water to flow 
away. This process should be continued until the water temperature is perceived to be constant. This 
operation  will  allow  the  mixed  water  temperature  to  increase  to  the  required  level  (if  the  mixer  valve 
option is specified) and permit the carer and/or user to check that the maximum temperature is safe 
prior  to  the  bather  entering  the  bath.  If  the  water  temperature  does  not  achieve  a  comfortable  level 
there may be a fault and the bath should not be used until the fault is rectified. Turn off the water, and 
allow any residual water in the bath to drain. If the temperature achieved was satisfactory, the bath is 
now ready for filling. Close the pop-up waste by operating the push-pull lever or depress the plug itself 
depending on which type is fitted. 

Summary of Contents for EASIBATH
























Reviews: