background image

Page 11 of 23 

To fill the bath 

 
If the bath has been supplied with a 

Reliance Caremix H3 Thermostatic Mixer Tap

 - 

Turn the mixer tap lever to start the flow of water, and leave in the desired temperature open position 
until the bath is full to the level required. To stop the flow turn the lever in the anticlockwise direction 
until the water stops. 
 

If the bath has been supplied with a 

Rada Authomerm-3 Thermostatic Mixer Tap

 - 

Turn the main flow lever to the right hand side of the unit, which will begin the water flow from the tap 
spout. To stop the flow, turn the lever to the middle position, above the spout. The temperature can be 
adjusted by using the temperature control knob on the top of the mixer tap. 

 

If the bath has been supplied with a Rada Sense Digital Adjustable Mixer Valve System -

 

The control panel can be mounted on the bath tub, a bracket or wall mounted near to the bath.  
Move your hand in front of the ‘bath fill’ symbol / sensor to start the flow of water. The temperature of 
the water can be increased by holding / waving a hand in front of the red ‘hot’ sensor on the right of 
the  control  panel.  The  temperature  of  the  water  can  also  be  reduced  by  holding  /  waving  a  hand  in 
front  of  the  blue  ‘cold’  sensor  on  the  left  of  the  control  panel.  Lights  will  indicate  where  between  the 
minimum  and  maximum  temperature  the  water  temperature  is  currently  set.  To  stop  the  bath  filling, 
hold / wave a hand in front of the ‘bath fill’ symbol.  
Care must be taken to not accidently activate the sensors when not wanted / required.  
 
The above bath fill options should be set to a maximum temperature of 43°C when the valve control is 
fully turned / set at its maximum. Always allow time for the mixed water to run through the systems. 
 

If the bath has the pre-set temperature On-Board Valves, simply open the tap on the bath to 
start the flow. 
 
If the bath has conventional hot and cold taps, simply turn them both on as required to get the 
desired mixed temperature.

 

 

REMEMBER:

 THE TEMPERATURE OF THE WATER MUST BE CHECKED ON EVERY OCCASION 

BEFORE A PERSON IS PLACED IN THE BATH OR THE SHOWER USED. 

 

To use the optional hand shower unit 

 

If the bath has been supplied with a Rada Authomerm-3 Thermostatic Mixer Tap - 

Turn the main flow lever to the left hand side of the unit, which will begin the shower flow. The lever 
automatically reduces the maximum hot water temperature by 3 degrees from the bath fill maximum 
temperature. The temperature can be adjusted by using the temperature control knob on the top of the 
mixer tap. 
 

If the bath has been supplied with a Rada Sense Digital Adjustable Mixer Valve System - 

The control panel can be mounted on the bath tub, a bracket or wall mounted near to the bath.  
Move your hand in front of the ‘shower’ symbol / sensor to start the flow of water. The temperature of 
the water can be increased by holding / waving a hand in front of the red ‘hot’ sensor on the right of 
the  control  panel.  The  temperature  of  the  water  can  also  be  reduced  by  holding  /  waving  a  hand  in 
front  of  the  blue  ‘cold’  sensor  on  the  left  of  the  control  panel.  Lights  will  indicate  where  between  the 
minimum and maximum temperature the water temperature is currently set. To stop the shower, hold / 
wave a hand in front of the ‘shower’ symbol.  
Care must be taken to not accidently activate the sensors when not wanted / required.  
 
The above shower options should be set to a maximum temperature of 39°C when the shower valve 
control is fully turned / set at its maximum.  
 

Be aware at first that the water may be quite cold; let it run for a short time to determine the 
steady temperature.

 Always allow time for the mixed water to run through the systems.

 

 
If the bath has the pre-set temperature On-Board Valves, simply open the shower tap to start 
the flow.

 

Summary of Contents for EASIBATH
























Reviews: