Kinghome KM09HFDI Instruction Manual Download Page 18

Free Match for North America

14

A.Single-Cored Wire

B.Mulit-Cored Wire

Insulating layer

Wiring Terminal

25

10

Fig.20

 WARNING!

① . 

If the power cord or the signal line is damaged, they must be replaced with the dedicated 

one.

② . 

Prior to the wiring, please check the voltage marked on the nameplate and then carry out 

the wiring following the wiring diagram.

③ . 

The dedicated power cord must be used for the air conditioning unit and the electrical 

leakage protection switch and air switch must be installed in case of the overload condition.

④ . 

The air conditioning unit must be earthed to prevent the hazard caused by the failed 

insulation.

⑤ . 

During the wiring, the wiring terminal or the single-core wire must be used; the direct wiring 

between the multi-core wire and wiring board would cause fire.

⑥ . 

All wiring should be done strictly in accordance with the wiring diagram; otherwise the 

improper wiring would cause the air conditioning unit running abnormally or damaged.

⑦ . 

Do not let the electric wires touch the refrigerant pipe, the compressor, the fan or other 

moving parts.

⑧ . 

Do not modify the wiring inside the indoor unit randomly; otherwise the manufacturer won’t 

assume any responsibility for the damage or abnormal running of the unit.

3.16  Wiring of the Power Cord (single-phase)

 

CAUTION!

The power supply for each indoor unit must be uniform.

① .

Dismantle the cover of the electric box of the indoor unit.

② .

Let the power cord go through the rubber ring.

③ .

Put the 4-core cable through the hole of the chassis and the bottom of the appliance 

upward, and then connect the power line and the communication line from the outdoor 
unit to the corresponding terminals N(1), 2, 3 , and grounding terminal of the indoor unit. 
Wiring shall be done properly as per the wiring diagram. (Note: Be sure the wring terminals 

A/B/C/D and piping joints A/B/C/D of the indoor unit match with that of the outdoor unit 

respectively).

④ .

Fix the power cord tightly with the binding wire.

KM36H4O

Summary of Contents for KM09HFDI

























Reviews: