background image

Page 4

COMPONENT LOCATIONS

Outside Antenna

mounted to ladder

Outside Antenna

mounted to roof

KC1241

Metal

Obstruction

Booster

Inside Antenna

The outside antenna must be completely above the roof line. 
Make sure the outside antenna does not exceed maximum vehicle height 

restrictions.
Locate outside antenna as far from metal obstructions as possible.
The mounting bracket allows the outside antenna to be mounted directly to 

the roof, or to a pole or ladder using the included pole mounting hardware. 

Mount booster as far away from outside antenna as possible, but make sure 

20 foot cable will still reach between the two.
A convenient place to mount the booster is to the inside back of a cabinet 

near a 110 VAC power source.  The booster can be oriented in any direction.

Place inside antenna as far away 

from booster as possible.

NOTE:

  It is up to the installer to determine the best component locations.  

We recommend you do a “soft install” first by placing all 

components in their chosen locations, completing the setup 

instructions, and verifying the system works as desired.   

(Route the cable through an open door or window for the 

soft install.)

TIP

Summary of Contents for KX1000

















Reviews: