background image

15

MIN. 

MAX 

1.

Turn off pump. Turn dial to O or Minimum. This reduces the fl ow 
of water into the unit when the cap is open.

Open the cap. For Model 400/430 pools use the cap tool 
included with New Water Cycler to loosen cap by hitting the 
handle with the fl at of your hand counterclockwise. Stand back 
to allow any chlorine fumes to dissipate.

The New Water Cycler Pacs 
are made of HDPE plastic. 
Non-refi llable container. Do not 
reuse or refi ll this container. 
Offer for recycling if available. 
Rinse thoroughly before 
recycling or discarding in trash.

Mark your calendar ahead for 
the approximate replacement 
times for the New Water Cycler 
Pac.

2.

7.

8.

3.

Cut handle from New Water Cycler Pac using a PVC 
cutting tool (KEEP OUT OF REACH OF CHILDREN)

3A.

 Find 

the indent in 
the plastic.

3B.

 Place curved section of 

tool around the narrow end 
of one pac tower and line up 
blade on indent

3C.

. Squeeze the handles 

together. Repeat for other side.  

3D.

. Make sure the blade 

comes straight across on the 
indent line for a clean cut.

3E.

 If openings are pinched 

together, open with fi ngers or 
re-cut closer to the colored 
screens inside New Water 
Cycler Pac. Leave at least 1/4” 
of plastic to fi t into New Water 
Cycler base.

4.

Invert New Water Cycler 
Pac and shake slightly until 
chlorine tablets fall into tower 
areas.

Insert New Water Cycler Pac 
into New Water Cycler, lining 
up the openings in New 
Water Cycler Pac with keys in 
New Water Cycler. 

NOTE:

 Openings are a 

different shape than keys.

Replace cap by hand only.

DO NOT OVERTIGHTEN.

DO NOT USE CAP TOOL TO 
TIGHTEN CAP.  
FOR REMOVAL ONLY.

5.

6.

PVC cutting tool 
available at local 
hardware stores.

Step 2: Putting the System to Work

A correct 
oval 
opening

Avoid a
pinched
opening.

Pac
towers

Pac 

towers

Indent in plastic

Model 120

Model 120

Model 400/430

Model 400/430

WARNING

Avoid sparks, smoking, or any open fl ame near 
New Water Cycler or chemicals.

DANGER

 

Never use fast dissolving chlorine tablets, liquid bleach, 
or calcium hypochlorite in the New Water Cycler.

p

IMPORTANT: 

Read the label on the New Water Cycler Pac  

 

 

carefully before using.

Finished cut ends

Model 120

Model 400/430

WE RECYCLE

WE RECYCLE

Summary of Contents for New Water 120

























Reviews: