GENERAL & SPECIFIC
SAFETY INSTRUCTIONS
VOLTAGE WARNING
: Before connecting the machine to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as
that specified on the nameplate. A power source with voltage greater than specified can result in SERIOUS INJURY to the user - as well as
damage the machine. If in doubt DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate is harmful to the
motor.
1. KNOW YOUR MACHINE
Read and understand the owners manual and labels affixed to
the machine. Learn its application and limitations as well as its
specific potential hazards.
2. GROUND THE MACHINE.
This machine is equipped with an approved 3-conductor cord
and a 3-prong grounding type plug to fit the proper grounding
type receptacle. The green conductor in the cord is the
grounding wire.
NEVER
connect the green wire to a live
terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting wrenches
are removed from the machine before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the
floor is clean and not slippery due to wax and dust build-up.
6. AVOID DANGEROUS ENVIRONMENT.
Don’t use machinery in damp or wet locations or expose them to
rain. Keep work area well lit and provide adequate surrounding
work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
Use padlocks, master switches or remove starter keys.
9. USE PROPER SPEED.
A machine will do a better and safer job when operated at the
proper speed.
10. USE RIGHT TOOL.
Don’t force the machine or the attachment to do a job for which
it was not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-slip
footwear is recommended. Wear protective hair covering to
contain long hair. Roll up long sleeves above the elbows.
12. ALWAYS WEAR SAFETY GLASSES.
Always wear safety glasses (ANSI Z87.1). Everyday eyeglasses
only have impact resistant lenses, they are
NOT
safety glasses.
Also use a face or dust mask if cutting operation is dusty.
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN MACHINE WITH CARE.
Keep machine clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
15. DISCONNECT MACHINE.
Before servicing, when changing accessories or attachments.
16. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ‘’OFF’’ position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the
instructions that accompany the accessories. The use of
improper accessories may cause hazards.
18. NEVER STAND ON TOOL.
Serious injury could occur if the machine tips over. Do not store
materials such that it is necessary to stand on the machine to
reach them.
19. CHECK DAMAGED PARTS.
Before further use of the machine, a guard or other parts that are
damaged should be carefully checked to ensure that they will
operate properly and perform their intended function. Check for
alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other
parts that are damaged should be properly repaired or replaced.
20. NEVER LEAVE MACHINE RUNNING UNATTENDED.
Turn power ‘’OFF’’. Don’t leave any machine running until it
comes to a complete stop.
SPECIFIC SAFETY INSTRUCTIONS
1. USE GUARD AND WEAR SAFETY GLASSES
To prevent bodily injuries during milling/drilling operations, always
use the safety guard and wear safety glasses.
2. NEVER DO “FREEHAND WORK”
Never do any work “Freehand” (hand holding the workpiece rather
than workpiece secured to the table). Always secure or clamp
workpiece before turning on machine.
3. USER MUST RECEIVE TRAINING bEFORE USE
.
The user must know the functions and principals of operation. The
user must also be familiar with the safety devices and regulations.
4. YOU ARE ENDANGERING YOURSELF
and other personel if you
bypass, remove or override a safety device such as the transparent
auto-shut-off spindle safety guard. Only use this milling/drilling if all
safety devices are working properly, if any are damaged or altered,
replace them with identical replacement parts.
5. CLEANING AFTER USE
Do not use your hands to clear metal chips, use protective gloves or
a brush.
6. SHARP CUTTING TOOL
Make sure the cutting tool is sharp, not damaged in any way and is
properly secured in the chuck.
7. NEVER TURN POWER ON
Never turn power on while the cutting tool is touching the workpiece.
8. SELECT PROPER SPEED
Make sure you select the correct and recommended speed for the
type of work and material you are cutting. Let the spindle reach
maximum speed before starting a cut.
