GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
1. TO AVOID INJURY FROM PARTS bEING THROWN bY
THE SPRING
Follow the instructions exactly as given and shown in “Adjusting
the quill return spring”.
2. USING A DRILL PRESS VISE
When using a drill press vise, always fasten it to the table.
3. NEVER DO “FREEHAND WORK”
Never do any work “Freehand” (hand holding the workpiece rather
than supporting it on the table) except when you have polishing to
do.
4. SECURE
the lock head to the column, table support to column
and table to table support before operating the drill press.
5. NEVER
move the head or table while the drill press is running.
6. USE THE RECOMMENDED SPINDLE SPEED
for the
specific operation and workpiece material. Check the panel inside
the guard cover for drill information. For accessories, use the in-
structions provided with the accessories.
7. NEVER
climb on the drill press table, it could break or pull the en-
tire drill press down on you.
SPECIFIC SAFETY INSTRUCTIONS FOR DRILL PRESS
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to the
tool. Learn its application and limitations as well as its specific po-
tential hazards.
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and a 3-
prong grounding type plug to fit the proper grounding type recep-
tacle. The green conductor in the cord is the grounding wire.
NEVER
connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the floor
is clean and not slippery due to wax and sawdust build-up.
6. AVOID DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations or expose them to
rain. Keep work area well lit and provide adequate surrounding
work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
-with padlocks, master switches or by removing starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when operated at the proper
speed.
10. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was
not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-slip
footwear is recommended. Wear protective hair covering to con-
tain long hair. Roll up long sleeves above the elbows.
12. ALWAYS WEAR SAFETY GLASSES.
Always wear safety glasses (ANSI Z87.1). Everyday eye-glasses
only have impact resistant lenses, thet are
NOT
safety glasses.
Also use a face or dust mask if cutting operation is dusty.
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN TOOL WITH CARE.
Keep tools sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
16. AVOID ACCIDENTAL STARTING.
Make sure the swich is in the ‘’OFF’’ position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the in-
structions that accompany the accessories. The use of improper
accessories may cause hazards.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool tips over. Do not store materi-
als such that it is necessary to stand on the tool to reach them.
19. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are
damaged should be carefully checked to ensure that they will oper-
ate properly and perform their intended function. Check for align-
ment of moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other parts that
are da -maged should be properly repaired or replaced.
20. NEVER LEAVE MACHINE RUNNING
UNATTENDED.
Turn power ‘’OFF’’. Don’t leave any tool running until it comes to a
complete stop.
