manualshive.com logo in svg

Kimball Fluent Series, Assembly Instructions Manual

Share
Download
Kimball Fluent Series Assembly Instructions Manual Download Page 15

Fluent

®

 

1  

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent. 
If you have any questions concerning these instructions, please call Kimball Office Customer Care. 

Part #02205358, Revision B 

Assembly Instructions 

Stacking Overhead on 
Highback Shelf 

Tools Required 

Hardware Required 

• 

Screw Gun w/ #2 Phillips Head Bit 

 

Note:

 It is recommended that two (2) persons be used to lift 

and place the overhead storage unit. 
1.  Carefully center the overhead storage unit and lower onto 

the highback shelf making sure that pucks are aligned and 
resting on top of one another. 

2.  All overhead storage units need to be fastened to the 

highback shelf using a #8 x 2 1/2” panhead screw. Using 
center row of holes on highback shelf pan, insert screw as 
close to center on each overhead securing it to the 
highback shelf. 

Installation 

• 

38 X 2 1/2” Panhead Screw 

Figure A 

Figure B 

Center row 

View From Underside of Highback Shelf 

Summary of Contents for Fluent Series


























Reviews:

No comments

Brands by name

Popular brands

Load more brands