2 / 8
P/N 55370159 • REV 2.0 • ISS 03OCT11
EN: Installation instructions
Installation
Caution:
For general guidelines on system planning, design,
installation, commissioning, use and maintenance, refer to the
CEN/TS 54-14 standard and local regulations.
To install a detector
Caution:
Always recalibrate optical smoke detectors before
first-time installation.
1. Insert the detector head into the mounting base and rotate
it clockwise until it clicks into place (Figure 1).
2. The detector may be locked into the mounting base if
required. To do this, remove the locking tab before
installation (Figure 2).
3. After installation, ensure that the detector communicates
with the control panel. If the detector does not
communicate with the control panel, check that duplicate
addresses have not been assigned.
4. Always test detectors after installation.
To remove a locked detector
1. Insert a small screwdriver into the locking tab slot (Figure
3).
2. Press and rotate the detector anticlockwise.
Addressing
Each device requires a numeric address between 1 and 125
for identification purposes. This is assigned at the fire panel or
using a PG700 portable address programmer.
Maintenance
Basic maintenance is reduced to a yearly inspection. Do not
modify internal wiring or circuitry.
To replace the optical chamber (KL731A only)
1. Remove the detector head from the mounting base.
2. Remove the detector cover by pressing the catch with a
screwdriver, turning and lifting (Figure 4).
3. Remove the existing optical chamber and insert the
replacement optical chamber (Figures 5 and 6).
4. Replace the detector cover and install detector head into
the mounting base.
To clean the optical chamber follow the above instructions for
removal and use compressed air to clear the dust.
Caution:
The detector must be recalibrated after cleaning or
replacement of the optical chamber.
Specifications
KL710A
KL731A
KL735A
Operating voltage
22 to 38 VDC
22 to 38 VDC
22 to 38 VDC
Current
Standby
(38V)
Alarm
250 µA
< 11 mA
250 µA
< 11 mA
350 µA
< 5 mA
Pre-alarm indication
Flashing LED
Flashing LED
Flashing LED
KL710A
KL731A
KL735A
Alarm indication
Constant LED
Constant LED
Constant LED
Coverage
60 to 80 m
2
60 to 80 m
2
60 to 80 m
2
IP rating
IP42
IP42
IP42
Compatible mounting
base
KZ700, KZ705,
KZ705D
KZ700, KZ705,
KZ705D,
KZ705R
KZ700, KZ705,
KZ705D
Temperature:
Operation
Storage
-10 to +60ºC
-10 to +70ºC
-10 to +60ºC
-10 to +70ºC
-10 to +60ºC
-10 to +70ºC
Relative humidity
(noncondensing)
10 to 95%
10 to 95%
10 to 95%
Colour White
White/Black
White
Dimensions (Ø × H )
99 × 45 mm
99 × 45 mm
99 × 51 mm
Weight
75 g
107 g
109 g
Certification and compliance
KL710A KL731A KL735A
Description
Heat detector
Optical smoke
detector
Dual heat /
smoke detector
Variant
--- KL731AB
---
Certification
CPD certificate
1134-CPD-007 1134-CPD-009 1134-CPD-012
Year of manufacture
The year of manufacture is included in the first two
digits of your product serial number (located on the
product identification label).
EN 54
EN54-5
EN54-7
EN54-5,EN54-7
Class A2
---
A2R
EMC EN
50130-4
EN 61000-6-3
EN 50130-4
EN 61000-6-3
EN 50130-4
EN 61000-6-3
Manufacturer
Shanghai UTC Fire & Security Electronics, 1st
Floor No. 2 Building No. 211, Qinqiao Road Jinqiao
Export Processing Zone, Pudong New Area
201206, Shanghai, China
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
ES: Instrucciones de instalación
Instalación
Precaución:
Para información sobre el diseño, instalación,
uso y mantenimiento del sistema, aconsejamos seguir la
norma CEN/TS 54-14 y normas locales.
Para instalar el detector
Atención:
Siempre recalibre los detectores ópticos antes de
su primera instalación.
1. Inserte el detector en la base y girar en sentido horario
hasta que encaje perfectamente (Figura 1).
2. El detector se puede bloquear en la base en caso de ser
necesario. Para ello, quitar la lengüeta antes de su
instalación (Figura 2).
3. Tras la instalación, asegurar que el detector comunica con
la central. Si el detector no comunica con la central,
verificar que no tenga asignada una dirección repetida.
