background image

4

3. Locations to be Avoided 

(Smoke Alarms)

•    In the garage. Products of combustion are present when you start your car. Only a Heat

Alarm is suitable in such locations

•    In front of forced air supply ducts used for heating and air conditioning, near ceiling fans, or

other high air flow areas.

•    Less than 10cm (4”) from the peak of an ‘A’ frame type ceiling.

•    In an area where the temperature may fall below 0°C or rise above 40°C. Such as garages

and unfinished attics; this should also include electrical boxes exposed to these environ-
ments..

•    In dusty areas. Dust particles may cause nuisance alarm or failure to alarm.

•    In very humid areas. Moisture or steam can cause nuisance alarms.

•    In areas where the Relative Humidity (RH) is above 93%.

•    Near fluorescent lights or CFL lamps.. Electronic “noise” may cause nuisance alarms.

•    In insect infested areas

•    Smoke alarms should not be installed within 0.9m (3ft) of the following: the door to a

kitchen,the door to a bathroom containing a tub or shower, ceiling or whole house ventilat-
ing fans orother high air flow areas..

•    Kitchens: Normal cooking may cause nuisance alarms. Only Heat Alarms are suitable for

use in Kitchens; they should also be fitted in integral garages.

•    Smoke alarms are not to be used with detector guards unless the combination (alarm and-

guard) has been evaluated and found suitable for that purpose.

4. Installing Alarm

These are mains powered alarms, so isolate the mains supply before commencing instal-
lation. 

They are for installation by a qualified electrician in accordance with the

current I.E.E. regulations

.

Select suitable location having regard to earlier advice.

Bring house wiring through a dry lining box into back of alarm; side entry, via mini
trunking is also possible by carefully knibbling away edge on trim-plate. Make good
joint, with white sealant, if necessary.

If alarm is not being interconnected,  interconnect cable terminal (I/O) on alarm is unused. 

(1)

a

b

C

1385-7206-00_R3_V9:-  2011.3.14  5:28 PM  Page 4

Summary of Contents for Fyrnetics Slick 1SFW











Reviews: