background image

 

P40 Plasma Cutting Machine 

|

 

P a g e

 

 

 

1.

 

Safety 

™

 

Welding may damage your body or others, so please take protection measure 
in operation 

™

 

Only ones who are trained professionally can install , debug, operate, maintain 

and repair the equipment. 

™

 

Do not maintain and repair the machine when the machine is connected with power. 

 

Electric shock can kill 
 

™

 

Never touch electrical parts. 

™

 

Wear dry, hole-free gloves and clothes to insulate yourself. 

™

 

Insulate yourself from work and ground using dry insulation. Make certain the insulation 

is large enough to cover your full area of physical contact with work and ground. 

™

 

Ensure to install the equipment correctly and ground the work or metal to be welded to a 

good electrical (earth) ground according the operation manual. 

™

 

Ensure to operate the equipment in safe position. 

 

Fumes and gasses can be dangerous 

 

™

 

Welding may produce fumes and gases hazardous to health. Avoid breathing 

these fumes and gases. When welding, keep your head out the fume. 

™

 

Using enough ventilation and/or exhaust at the arc to keep fumes and gases away from the 

breathing zone. 

 

Welding sparks can cause fire or explosion 
 

™

 

Remove fire hazards from the welding area. If this is not possible, cover 

them to prevent the welding sparks from starting a fire. Remember that welding sparks 

and not materials from welding can easily go through small cracks and openings to 

adjacent areas. 

 

Do not weld enclosed tanks or containers 

 

™

 

Prohibit to use welder to unfrozen. 

™

 

Have a fire extinguisher readily available. 

 

Hot parts can lead to burn 
 

Summary of Contents for P40

















Reviews: