11
Kice Industries, Inc.
012420 / FLT-M02-0004
Safety Precautions Continued
•
If a Kice Venturi-Jet filter is equipped with a maintenance panel incorporating any Protective Interlocking Limit Switch
(PLS), the PLS must be interlocked with all electrical controls so that all motors or powered devices on the unit will
be de-energized if any protected cover, guard, grate, or maintenance panel is open or removed. Never attempt to
manually override or electrically bypass the PLS safety device. Interlock function of the PLS must be tested and
logged daily by supervisory personnel.
•
Kice Venturi-Jet filters must be equipped with a properly functioning Protective Interlocking Electrical Control Switch
(PCS), a Pad-lockable Manual Power Lockout Switch, along with the other basic safety equipment listed above. On-
Off, interlock and padlock functions of the PCS must be tested and logged periodically by supervisory personnel.
•
Any device powered by air or hydraulic pressure must be equipped with a properly functioning Padlockable Manual
Pressure Lockout and Internal Pressure Relief Valve (PLV) capable of safely relieving motive pressure between the
isolation valve and device.
•
Any Kice Venturi-Jet filters used in the processing of combustible materials or in hazardous environments require
evaluation by the owner and regulatory bodies to determine appropriate Kice Venturi-Jet filters monitoring equipment,
dust control, explosion protection and electrical equipment enclosures. Do not use a Kice Venturi-Jet filter in
hazardous environments unless properly equipped for the hazard.
•
Operate safely at all times. Use personal protective equipment (PPE) such as hard hats, helmets, gloves, earplugs,
protective eyewear, etcetera when and where appropriate. Keep PPE in good repair and accessible to affected
personnel.
•
Keep the workplace clean and free of dirt and dust at all times. Do not attempt to work on slippery or unsafe surfaces,
ladders or work platforms when maintenance or repair work is being performed on an Kice Venturi-Jet filter.
• The Operator must ensure that all piping and connections are laid away from access routes, ladders and steps.
• Adequate and proper lighting must be provided at the equipment location.
• Do not use a ladder or work platform unless it is in good repair and rated for the load required to complete required
Kice Venturi-Jet filter service.
•
Never stand under any kind of hoists or lifting mechanisms whether or not it is loaded or in operation. Never stand
under or near an Kice Venturi-Jet filter or component when it is being lifted.
•
All Kice Venturi-Jet filter lifting devices must be inspected by qualified personnel before each use. Do not use a lifting
device to transport a Kice Venturi-Jet filter. Never use a lifting device that is damaged, deteriorated or in need of
repair.
•
The unit must be lifted by a means with sufficient lifting capacity.
• The operator must ensure that adequate lighting conditions are provided at the location of equipment operation.
•
Never allow any kind of metal or other foreign objects to enter a Kice Venturi-Jet filter while in operation, unless the
system is specifically designed as a wire or metal reclaim system. Examined raw materials should be used through
the machine to ensure proper and consistent operation. A material separator should be installed on the raw gas inlet.
•
Special attention must be devoted to outside contractors engaged to enter and perform work on a Kice Venturi-Jet
filter or in the workplace. Special care must be exercised to ensure all such personnel are fully informed of potential
hazards and plant safety procedures. Special emphasis should be placed on the use of explosion proof electrical,
cutting, or welding tools where required.
• Free outlet of product must be guaranteed at all times. Otherwise, blockage and severe damage may result, or a
dangerous situation may occur.
•
Airflow to the filter must be switched off long enough (approximately 30 minutes) for dust to settle in the raw gas or
dirty air chamber before the service entrance is opened. This is to prevent zone entrainment and mitigate the risk of a
potential event outside the system.
• Drive components must be inspected and adjusted after transportation and periodically as required by operating
conditions. Check sprocket, sheave and coupling alignment and spacing, drive belt tension, setscrews, keys,
fasteners, bearings, shafts, and motors as appropriate to job conditions.
•
It is ultimately the operator’s responsibility to apply the above listed precautions and ensure proper Kice Venturi-Jet
filter use, maintenance and lubrication. Keep these instructions and list of warnings with your machine at all times.
• It cannot be assumed that every acceptable safety procedure is contained herein or that abnormal or unusual
circumstances may not warrant or require additional procedures.