background image

IMPORTANT SAFETY INSTRUCTIONS

Inside you will find many helpful hints on how to use and maintain your air conditioner
properly. Just a little preventive care on your part can save you a great deal of time
and money over the life of your air conditioner. You'll find many answers to common
problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting
Tips first, you may not need to call for service at all.

To prevent injury to the user or other people and property damage, the following
instructions must be followed. Incorrect operation due to ignoring of instructions may
cause harm or damage. The seriousness is classified by the following indications.

This symbol indicates the possibility of death or serious injury.

Always do this.

Never do this.

CAUTION

This symbol indicates the possibility of injury or damage to property.

WARNING

WARNING

Plug in power plug
properly.

Do not modify power cord length or share the
outlet with other appliances.

Always ensure effective
grounding.

Unplug the unit if strange
sounds, smell, or smoke
comes from it.

Keep firearms away.

Ventilate room before operating air conditioner if there is
a gas leakage from another appliance.

Otherwise, it may cause electric
shock or fire due to

heat

generation.

excess

It may cause electric shock or fire due to heat generation.

Incorrect grounding may cause
electric shock.

It may cause fire and electric
shock.

It may cause fire.

It may cause explosion, fire and, burns.

It may cause electric shock or fire
due to heat generation.

It may cause electric shock.

It may cause failure of machine
or electric shock.

It may cause fire and electric
shock.

It may cause fire and electric
shock.

It may cause electric shock or fire.
If the power cord is damaged, it must be replaced by the
manufacturer or an authorised service centre or a similarly
qualified per son in order to avoid a hazard.

This could damage your health.

Incorrect installation may cause
fire and electric shock.

It may cause electric shock.

It may cause an explosion or fire.

It may cause failure and electric shock.

Do not operate or stop the
unit by inserting or pulling
out the power plug.

Do not operate with wet
hands or in damp
environment.

Do not allow water to run
into electric parts.

Do not use the socket if it is
loose or damaged.

Do not use the power cord
close to heating appliances.

Do not damage or use an unspecified power
cord.

Do not direct airflow at room occupants only.

Always install circuit
breaker and a dedicated
power circuit.

Do not open the unit during operation.

Do not use the power cord near flammable gas
or combustibles, such as gasoline, benzene,
thinner, etc.

Do not disassemble or modify unit.

READ THIS MANUAL

1

Summary of Contents for KSTAT12-1B




























Reviews: