manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 89 / 276

Share
Download
Keysight N9923A User Manual Download Page 89

 89

Keysight N9923A Handheld Analyzer
User’s Guide

6

DTF (Distance to Fault) Measurements

CAT Mode 

Distance to Fault

 (DTF) measurements are generally used to locate 

problems, or faults, in a length of cable or transmission line. In this chapter, the 

cable to be tested is referred to as the DUT (Device Under Test).

Settings that are NOT unique to DTF measurements are documented in 

Chapter 5, 

“CAT (Cable and Antenna Test) Mode”, on page  75

.

In this Chapter

Optional settings

“How to make DTF Measurements” on page 90

“DTF Settings Table” on page 91

“DTF Measurement (Format)” on page 91

“DTF Start and Stop Distance” on page 92

“Frequency Mode” on page 92

“Coupled Frequency” on page 93

“Cable (Correction) Specifications” on page 94

“Window Settings” on page 97

“DTF Units” on page 98

“Calculated DTF values” on page 98

“About Alias Faults” on page 98

“All about Markers” on page 174

“All about Limit Lines” on page 185

“Saving and Recalling Files” on page 192

Trace Math is NOT available in DTF Measurements.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments