Keysight N9923A User Manual Download Page 98

Page: 98 / 276

98 Keysight N9923-90001 User’s Guide

DTF (Distance to Fault) Measurements
DTF Measurement Settings

DTF Units

The DTF Units setting is available ONLY on the DTF Settings table.

By default, X-axis units for DTF measurement settings are displayed in Meters.

How to change DTF units

— With a DTF measurement present, press

Freq/Dist

— Then

More

then

Distance Unit m feet

— The current selection is underlined

m (meters) Feet

Calculated DTF values

Press

Next Page

on the DTF Settings Table to view the following

calculated

Value

s noted on the FieldFox screen with c - <setting>

Start Frequency

– Start frequency that is used to calculate DTF.

Stop Frequency

– Stop frequency that is used to calculate DTF.

Range Resolution

. Indicates the accuracy of the distance to fault

measurement. For example, with range resolution of 500 mm, if the distance to
fault is 10 meters, this value could be inaccurate by +/- 500 mm or between

9.5 to 10.5 meters. This value is calculated from frequency span / resolution
(points).

Response Resolution, not displayed, indicates the distance that could be
between two faults and still show as separate faults. Learn more in

“Window

Settings” on page 97

Maximum Distance

. The distance that could be viewed with the current

settings. Defined by: Vf*c*Points/(2*Bandwidth) where:

— Vf = velocity factor

— c = speed of light

— Points = resolution

— Bandwidth = frequency range
Alias-free Range (On/Off)

— On = No Alias images

— Off = Alias images may appear in the response.

About Alias Faults

An alias fault is not a true device response. An alias fault appears because of
the method used to convert frequency to time.

On the DTF Settings page (above) the c - Alias-free Range = Off setting
indicates alias images MAY appear on the screen.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 98 / 276

Search results

Summary of Contents for N9923A

Reviews: