Keysight N6705 Service Manual Download Page 56

Page: 56 / 135

3 Calibration

Model N6705 Service Guide

Voltage Common Mode Rejection Ratio Calibration

Step 1. For this step, make the connections shown in Cal Setup C.

Connect an external jumper between the +sense and the

−

sense

terminals. Connect a second jumper from the +output to the

−

sense

terminal. For models N6761A and N6762A only, connect a 25

Ω load

resistor across the +output and –output terminals.

This procedure is automatic and only takes a few seconds.

Front Panel:

SCPI Command:

From the Calibration menu, select
Miscellaneous, Common Mode Rejection
Ratio, then Start. Then select Close.

CAL:VOLT:CMRR

(@1)

*OPC?

After calibration completes, disconnect all jumpers and resistors.

Current Calibration

High Range Programming and Measurement

The output voltage may go negative at some point during this procedure
on units that have polarity reversal relays (Option 760).

Step 1. Connect a precision shunt resistor to the output. The shunt resistor

should be able to measure at least 120% of the output’s full-scale
current (see Cal Setup B). Connect the Keysight 3458A across the shunt
resistor.

Step 2. Select the full-scale current programming range. The value to program a

range must be the maximum current of the range. This example selects
the 3 A full-scale range of output 1. Full-scale ranges vary according to
model.

Front Panel:

SCPI Command:

From the Calibration menu, select Current,
High Range Prog and Meas. Then select Start.

CAL:CURR 3

, (@1)

Step 3. Select the first current calibration point.

Front Panel:

SCPI Command:

The first calibration point is automatically
selected. “Enter P1 measured data” should be
displayed.

CAL:LEV P1
*OPC?

Step 4. Calculate the shunt current (I=V/R) and enter the data.

Front Panel:

SCPI Command:

Enter the calculated value into the data field
and then select Next.

CAL:DATA <data>

Summary of Contents for N6705








































































































































Search results

Summary of Contents for N6705

Reviews:

Brands by name

Popular brands

Keysight N6705, Service Manual

Search results

Summary of Contents for N6705

Reviews:

Brands by name

Popular brands