manualshive.com logo in svg

Keysight N6705, Service Manual

Share
Download
Keysight N6705 Service Manual Download Page 13

Performance Verification    2 

Model N6705 Service Guide 

13 

Verification Procedure 

Constant Voltage Tests 

NOTE

 

Test each output channel individually. Refer to the appropriate test 
record form for the instrument settings of the model you are checking. 

Voltage Programming and Readback Accuracy 

Test category = performance, calibration 

This test verifies that the voltage programming and measurement 
functions are within specifications.  

1

 

Turn off the DC Power Analyzer and connect a 

DMM

 across the sense 

terminals (see Test Setup A). Do not connect the load. 

2

 

Turn on the DC Power Analyzer and program the instrument settings 
as described in the test record form under “Voltage Programming & 
Readback, Min Voltage”. Turn the output on. 
The output status should be “CV” and the output current should be 
close to zero. 

3

 

Record the output voltage reading from the DMM and the voltage 
measured over the interface. The readings should be within the limits 
specified in the test record form for the appropriate model under 
“Voltage Programming & Readback Minimum Voltage”. 

4

 

Program the instrument settings as described in the test record form 
under “Voltage Programming & Readback High Voltage”. 

5

 

Record the output voltage reading from the DMM and the voltage 
measured over the interface. The readings should be within the limits 
specified in the test record form for the appropriate model under 
“Voltage Programming & Readback High Voltage”. 

6

 

For models N6761A, N6762A, N6781A, N6782A, and N6784A only.

 

Set both the voltage programming and the voltage measurement to 
the low range (5.5 V for models N676xA; 6 V programming and 1 V 
measurement for models N678xA). Set the instrument as described 
under “Voltage Programming & Readback, Low Voltage”. Repeat 
step 5 for the low voltage range. The readings should be within the 
limits specified under “Voltage Programming & Readback Low 
Range”. 

7

 

For models N6781A, N6782A, and N6784A only.

 Set the voltage 

programming to the 600 mV range and the voltage measurement to 
the 100 mV range. Set the instrument as described under “600 mV 
Programming & 100 mV Readback”. Repeat step 5. The readings 
should be within the limits specified under “600 mV Programming & 
100 mV Readback”. 

8

 

For models N6763A – N6766A only.

 Set the instrument as described 

under “Voltage Readback, Low Voltage”. Record the voltage measured 
over the interface. The reading should be within the limits specified 
under “Voltage Readback Low Range”. 

Summary of Contents for N6705








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands