manualshive.com logo in svg

Keysight N6705, Service Manual

Share
Download
Keysight N6705 Service Manual Download Page 49

Calibration    3 

Model N6705 Service Guide 

49 

Calibration Procedure – Models N675xA 

Enter Calibration mode 

Front Panel:

 

SCPI Command: 

Press [Menu], then select Utilities, 
Administrative Tools, Administrator Login. 
Enter your numeric password in the PIN 
field and select Login. 
Then select the Calibration menu. Select 
Turn On/Off to access the menu items. 

CAL:STAT ON, 

<password>

 

Voltage Calibration 

High Range Programming and Measurement 

Step 1. Connect the voltage input of the Keysight 3458A to an output channel 

(see Cal Setup A). 

Step 2. Select the full-scale voltage programming and measurement range. The 

value entered must be the maximum voltage of the range that you are 
calibrating. This example selects the 50 V full-scale range of output 1.  
Full-scale ranges vary according to model. 

 

Front Panel:

 

SCPI Command: 

From the Calibration menu, select Voltage, 
High Range Prog and Meas. Then select 
Start. 

CAL:VOLT 50

, (@1)

 

Step 3. Select the first voltage calibration point. 

 

Front Panel:

 

SCPI Command: 

The first calibration point is automatically 
selected. “Enter P1 measured data” should be 
displayed. 

CAL:LEV P1 
*OPC?

 

Step 4. Measure the output voltage with the DMM and enter the data. 

 

Front Panel:

 

SCPI Command: 

Enter the value from the external DMM into 
the data field and then select Next. 

CAL:DATA <data>

 

Step 5. Select the second voltage calibration point. 

 

Front Panel:

 

SCPI Command: 

The second calibration point is automatically 
selected. “Enter P2 measured data” should 
be displayed. 

CAL:LEV P2 
*OPC?

 

 

Summary of Contents for N6705








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands