Keysight Technologies N9038A MXE Installation Note Download Page 4

Page: 4 / 24

Installation Note N9038-90039

Option EXM – External Mixing Upgrade

What you will find in this Document

ESD Information ...............................................................................................................

page 5

Contents ...........................................................................................................................

page 7

Tools Required..................................................................................................................

page 8

Initial Instrument Functionality Check ............................................................................

page 9

Instrument Operating System Requirement Verification................................................

page 9

Frequency Range Option Determination.........................................................................

page 9

Overview .........................................................................................................................

page 10

Outer Hardware Removal...........................................................................................

page 10

Front End Assembly Cable Installation......................................................................

page 10

Instrument Button Up ................................................................................................

page 20

Initial Instrument Power Up .......................................................................................

page 20

License Key Retrieval and Installation.......................................................................

page 21

Instrument Software Installation ...............................................................................

page 21

Upgrade Installation Verification ...............................................................................

page 22

Adjustments and Performance Verification ..................................................................

page 23

Manual Procedures Required ...................................................................................

page 23

Automated Utilities Required ...................................................................................

page 23

Automated Adjustments Required ...........................................................................

page 23

Automated Performance Verification Testing Required ..........................................

page 23

Summary of Contents for N9038A MXE

























Search results

Summary of Contents for N9038A MXE

Reviews:

Related manuals for N9038A MXE

Brands by name

Popular brands

Keysight Technologies N9038A MXE, Installation Note

Search results

Summary of Contents for N9038A MXE

Reviews:

Related manuals for N9038A MXE

Brands by name

Popular brands