manualshive.com logo in svg

Key Digital KD-WP8, Setup And Programming Manual

Share
Download
Key Digital KD-WP8 Setup And Programming Manual Download Page 36

521 East 3

rd

 

Street Mt. Vernon, NY 10553 • www.keydigital.com 

Rev 1.2 

– March. 2021 

 

 

 

 

36 

Status 

Description 

Image 

Firmware Update 

While updating firmware, LEDs fill 

Blue 

& 

Red 

from the top to bottom quickly. 

BLUE 

-> 

RED 

-> 

BLUE

…. 

This LED display pattern repeats while 
firmware updates. 
 

Note: Web UI supports firmware 
update via IP only. KDMS Pro supports 
firmware update via USB and IP. 

 

Event Execute Failure 

When a button is pressed on a Keypad 
with project loaded, that button LED 
will blink 

Red twice 

if KD-WP8 cannot 

reach the controlled device. 

The problem may be caused by an 
incorrect IP address or IP Port, or that 
the controlled device has disconnected 
from the network.  

 

Lock / Unlock Keypad 

When locking via 3 second key combo 
hold, 

all LEDs flash Red twice. 

When unlocking via 3 second key 
combo hold, 

all LEDs flash Blue twice

. 

If the keypad is locked, and user is 
tries to press button for control, 

all 

LEDs flash Red twice 

to indicate the 

keypad is locked. 

 

Note: Use the lock function to protect 
from unauthorized usage, for example 
in a classroom. 

 

 

 

 

 

Summary of Contents for KD-WP8









































Reviews:

No comments

Brands by name

Popular brands

Load more brands