background image

 

o

  - Furnaces installed in hobby or craft rooms 

o

  - Furnaces installed near chemical storage areas 

o

  Exposure to the following substances in the combustion 

air  supply  may  also  require  OUTDOOR  AIR  for 
combustion: 

  - Permanent wave solutions 

  - Chlorinated waxes and cleaners 

  - Chlorine based swimming pool chemicals 

  - Water softening chemicals 

  - De-icing salts or chemicals 

  - Carbon tetrachloride 

  - Halogen type refrigerants 

  - Cleaning solvents (such as perchloroethylene) 

  - Printing inks, paint removers, varnishes, etc. 

  - Hydrochloric acid 

  - Cements and glues 

  - Antistatic fabric softeners for clothes dryers 

  - Masonry acid washing materials 

WARNINGS 

 

NEVER burn garbage or paper in the unit. 
NEVER store combustible material around it. 

 

CAUTION 

 

DO  NOT  START  THE  BURNER  UNTIL  ALL  FITTINGS,  COVERS  AND  DOORS  ARE  IN 
PLACE.    DO  NOT  TAMPER  WITH  THE  FURNACE  OR  CONTROLS,  CALL  A  QUALIFIED 
BURNER  TECHNICIAN.    DO  NOT  STORE  OR  USE  GASOLINE  OR  OTHER  FLAMMABLE 
VAPOURS AND LIQUIDS IN THE VICINITY OF THIS UNIT OR ANY OTHER APPLIANCE. 

DANGER 

 

Do not use this furnace as a construction heater. Use of this furnace as a construction 
heater exposes it to abnormal conditions, contaminated combustion air and lack of air 
filtering. Failure to follow this warning can lead to premature furnace failure which could 
result in a fire hazard and/or bodily harm and/or material damage. 

 

IMPORTANT 

 

This  manual  contains  instructional  and  operational  information  for  the  GEMINI  3T  &  5T/ 
ECLIPSE 3T OIL-FIRED FRONT / REAR FURNACE.  Read the instructions thoroughly before 
installing  furnace  or  starting  the  burner.    Consult  local  authorities  about  your  local  FIRE 
SAFETY REGULATIONS.  All installations must be in accordance with local state or provincial 
codes.  Improper installation will result in voiding of warranty. 
 
THE INSTALLATION OF YOUR GAS-FIRED FURNACE MUST CONFORM TO THE 
REQUIREMENT OF THE AUTHORITY HAVING JURISDICTION OR IN

 THE ABSENCE 

OF SUCH REQUIREMENTS, TO THE NATIONAL FUEL GAS CODE ANDSI Z223.1/NFPA 
54 AND/OR NATIONAL GAS AND PROPANE INSTALLATION CODE CAN/CSA B149.1

.  

Summary of Contents for ECLIPSE 3T




































Reviews: