manualshive.com logo in svg

KERN VHT, Operating Manual, Page: 25 / 26

Share
Download
KERN VHT Operating Manual Download Page 25

9  Error messages 

 

Error 

Possible cause 

Remedy 

 

 

 

Err01 

Signal of the weighing cell unstable 

Automatic 

 

 

 

Err02 

Balance overloaded 

Automatic after unloading 

 

 

 

Err03 

Gross negative. This action is not allowed 

Automatic 

 

 

 

Err04 

Outside the zero range 

Press any button 

 

 

 

Err05 

Exactness of piece calculation insufficient 

Press any button 

 

 

 

Err06 

Load cell signal too high 

Automatically to correction 
and input 

 

 

 

Err07 

Load cell signal too low 

Automatically to correction 
and input 

 

 

 

Err08 

Calibration outside the range (negative) 

Automatic 

 

 

 

Err09 

Calibration outside the range (signal too low) 

Automatic 

 

 

 

Err10 

Calibration value of the 2nd (3rd) point lower 
than the value of the 1st (2nd) point 

Automatic 

 

 

 

Err11 

Calibration from piece counting mode 

Automatic 

 

 

 

Err97 

Calibration blocked 

Automatic 

 

 

 

Err98 

The calibration value must be higher than the 
previous one 

Automatic 

 

 

 

Err99 

Actuation only allowed on the display device 

Automatic 

 

VHT-BA-e-0910 

25

Summary of Contents for VHT



























Reviews:

No comments