SIGNALING-3
5
Enter your desired DCS code using the microphone keypad.
•
Refer to the table below for DCS codes.
DCS Code
023
025
026
031
032
036
043
047
051
053
054
065
071
072
073
074
114
115
116
122
125
131
132
134
143
145
152
155
156
162
165
172
174
205
212
223
225
226
243
244
245
246
251
252
255
261
263
265
266
271
274
306
311
315
325
331
332
343
346
351
356
364
365
371
411
412
413
423
431
432
445
446
452
454
455
462
464
465
466
503
506
516
523
526
532
546
565
606
612
624
627
631
632
654
662
664
703
712
723
731
732
734
743
754
DCS CODE SCAN
This function scans through all DCS codes to identify the
incoming DCS code on a received signal. You may fi nd it useful
when you cannot recall the DCS code that the other persons in
your group are using.
1
Press
[TONE]
3 times to activate the DCS function.
• The
icon appears on the display when the DCS function is
ON.
•
Each press of
[TONE]
changes the selection as follows:
Tone
(
)
➡
CTCSS (
)
➡
DCS (
)
➡
Cross Tone (
:
default)
➡
Off (no display).
2
Press
[F], [T.SEL] (1s)
.
• The
icon blinks and “SCAN” appears on the display.
•
Scan starts when a signal is received.
•
To reverse the scan direction, turn the
Tuning
control clockwise
(upward scan) or counterclockwise (downward scan). You can
also press microphone
[UP]
/
[DWN]
.
•
To quit the scan, press
[ESC]
.
•
When a DCS code is identifi ed, the identifi ed code appears on
the display and blinks.
3
Press
the
Tuning
control to program the identifi ed code in
place of the currently set DCS code.
•
The DCS function will remain ON. To cancel DCS, press
[TONE]
until DCS no longer appears on the display.
• Press
[ESC]
if you do not want to program the identifi ed code.
• Rotate
the
Tuning
control while an identifi ed code is blinking, to
resume scanning.
USING CROSS TONE
You can set separate signaling types by TX and RX for when you
access a repeater that uses different Encode/ decode signaling.
To turn the Cross Tone function On:
Press
[TONE]
4 times to activate the Cross Tone function.
• The
“
” (default) icon appears on the display when the Cross
Tone function is On.
•
Each press of
[TONE]
changes the selection as follows:
Tone
(
)
➡
CTCSS (
)
➡
DCS (
)
➡
Cross Tone (
:
default)
➡
Off (no display).
■
Selecting a Cross Tone mode
To select the cross tone/code frequency required to access
your desired repeater:
1
Turn the Cross Tone function On.
2
Press
[F], [T.SEL]
.
•
The Cross Tone setting appears on the display.
3
Rotate
the
Tuning
control to select your desired Cross
Tone setting.
Setting
Encode
Decode
Icon
DCS OFF
DCS
off
TO DCS
Tone
DCS
DCS CT
DCS
CTCSS
TO CT
Tone
CTCSS
•
To exit the Cross Tone setting selection, press
[ESC]
.
4
Press any key other than the
Tuning
control and
[ESC]
to
complete the setting.