Kenwood TK-190 Instruction Manual Download Page 6

Page: 6 / 32

PREPARATION

Match the four grooves

of the battery pack

with the corresponding

guides on the back of

the transceiver.

Slide the battery pack

along the back of the

transceiver until the

release latch on the

base of the transceiver

locks.

To remove the battery

pack, pull back on the

release latch and slide

the pack away from the

transceiver.

■

Installing/ Removing the Optional Battery Pack

Charge the battery pack before use.

◆

DO NOT RECHARGE THE BATTERY PACK IF IT IS FULLY

CHARGED; YOU MAY INADVERTENTLY SHORTEN THE

BATTERY PACK LIFE OR DAMAGE THE BATTERY PACK.

◆

AFTER RECHARGING THE BATTERY PACK, REMOVE

IT FROM THE CHARGER. IF THE CHARGER POWER

IS RESET (TURNED ON AFTER BEING TURNED OFF),

RECHARGING WILL COMMENCE AND THE BATTERY

PACK WILL BECOME OVERCHARGED.

◆

DO NOT SHORT CIRCUIT THE BATTERY TERMINALS.

◆

DO NOT DISPOSE OF THE BATTERY BY FIRE.

◆

DO NOT ATTEMPT TO REMOVE THE CASING FROM THE

BATTERY PACK.

Summary of Contents for TK-190

































Search results

Summary of Contents for TK-190

Reviews:

Related manuals for TK-190

Brands by name

Popular brands

Kenwood TK-190, Instruction Manual

Search results

Summary of Contents for TK-190

Reviews:

Related manuals for TK-190

Brands by name

Popular brands