background image

0

SIGNALLING

  2-Tone Signalling

Note:

  This transceiver is only capable of decoding -Tone signals.  It 

cannot encode a -Tone signal.

  A -Tone call will be cancelled if you change the channel or 

turn Scan ON.

  -Tone Signalling is either activated or deactivated 

by your dealer.  Using this function, you will only hear 

calls that are intended for you to hear.

  When you receive a call with a -Tone signal that 

matches the two tones set up in your transceiver, 

squelch opens and you will hear the call.

•  When a correct -Tone signal is received, the CALL LED 

(orange) will flash and the display will alternate between 

“CALL” and the current channel number (or name).

  While responding to the call by pressing the 

PTT

 

switch and speaking into the microphone, the TX 

LED (red) will light, and only the channel number (or 

name) will appear on the display.

•  When you release the 

PTT

 switch, the LED will flash 

either red or orange, and the display will either alternate 

between “CALL” and the channel number (or name) or 

it will only display “CALL”.  This depends on how your 

dealer sets up -Tone Signalling.

•  If your dealer programmed Transpond for -Tone 

Signalling, your transceiver will automatically send an 

acknowledgment signal to the station that called you.

•  If your dealer programmed Tone Alert for -Tone 

Signalling, a tone will sound when the correct -Tone 

signal is received.

Summary of Contents for TK-190

































Reviews: