463843104 • 21
After Lighting
HI
Do not lean over grill while lighting.
1. Open lid.
2.
3.
HI
4.
HI
After Lighting:
HI
: Leave knobs on
position for warm-up.
Turn on gas at LP tank.
Place lit match into match-lighting hole from outside grill
bottom (as shown below).
Push in and turn right knob to
. Be sure burner lights and
stays lit.
Light other burners by pushing knobs in and turning to
.
Leave knobs on
for warm-up.
Match-Lighting
s
Match-lighting hole in
side of grill bottom.
Ignitor Lighting The Sideburner
Match Lighting
1.
2.
HI
3.
4.
1.
2.
HI
Turn on gas at LP tank.
Push in and turn sideburner knob to
.
Press and hold ignitor button to light. Be sure burner lights and
stays lit.
If burner does not light, turn sideburner knob to
, wait 5
minutes, try again.
Turn on gas at LP tank.
Hold a lit match to any port on the sideburner. Push in and
turn the sideburner knob to
. Be sure burner lights and stays
lit.
OFF
CAUTION
If burner does not light, turn knobs to
, wait 5
minutes, and try again. If the burner does not ignite with
the valve open, gas will continue to flow out of the burner
and could accidently ignite with risk of injury.
OFF
Burner Flame Check
• Light burner, rotate knobs from HI to LO. You should see a
smaller flame in LO position than seen on HI. Always check
flame prior to each use. Perform flame check on sideburner. If
only low flame is seen refer to "Sudden drop or low flame" in
the
.
Troubleshooting Section
HI
LO
Turning Grill Off
Ignitor Check
Valve Check
Hose Check
General Grill Cleaning
• Turn all knobs to
position. Turn LP tank off by turning
hand-wheel clockwise to a full stop.
Press and hold ignitor button. "Click"
should be heard and spark seen each time between collector
box or burner and electrode. See
if no click
or spark.
. Knobs lock in
position. To check valves, first push
in knobs and release, knobs should spring back. If knobs do
not spring back, replace valve assembly before using grill. Turn
knobs to
position then turn back to
position. Valves
should turn smoothly.
Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only identical
Kenmore replacement valve/hose/regulator assembly.
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory
. Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry.
Wash grate and vaporiser bars with
concentrated grill cleaner or use soap and water solution. Dry
thoroughly and store indoors between cookouts.
•
Wash with warm soapy water and wipe dry.
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
• Turn gas off at LP tank.
• Important: Make sure gas is off at LP tank before checking
valves
LO
•
(and should never be painted)
Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plated wire grate:
Plastic parts:
• Porcelain grates:
"Troubleshooting"
s
OFF
OFF
OFF
Before Your First Cookout
• Light burners, check to make sure they are lit, close the lid and
warm up grill on HIGH for 15 minutes. Heating of paint and
parts will produce an odor only on first lighting.
Summary of Contents for 415.162080
Page 27: ...463843104 27 ...