Kenmore 415.162080 Assembling Instructions Download Page 6 | Manualshive

Page: 6 / 28

background image

6 • 463843104

ASSEMBLY – Model No. 415.162080

1

Cart Assembly Step 1

Position base on edge with tank hole to left side.
Insert legs into base and attach with carriage bolts
and plastic wing nuts. DO NOT FULLY TIGHTEN.
Insert midshelf into holes on insides of legs, long
wires toward left side. Fully tighten carriage bolts
and plastic wing nuts.

Leg Assembly

Long midshelf wire
to left side.

Base

5

4

USE TOP HOLE

IMPORTANT!

5

Qty. 8

(Plastic)

4

Qty. 8

«
...
4
5
6
7
8
...
»

Summary of Contents for 415.162080





























Reviews:

No comments

Related manuals for 415.162080

Brand: recteq Pages: 27

Brand: Raider Pages: 68

GR2297802-MM-00

Brand: Rankam Pages: 52

Brand: YATO Pages: 44

Brand: Barbecook Pages: 122

Brand: MICRO CHEF GRILL Pages: 60

Brand: Gasmate Pages: 16

Brand: Parkside Pages: 108

Hall MicroPower 6020-026

Brand: ConMed Pages: 40

Brand: Parkside Pages: 77

1PBF0306BQ 00 Series

Brand: Barazza Pages: 24

Brand: Narex Pages: 16

Brand: Barbecook Pages: 400

Brand: Margaritaville Pages: 12

Brand: Napoleon Pages: 20

Brand: Narex Pages: 32

Brand: Monument Grills Pages: 21

Brand: Klarstein Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands