Kenmore 363.71542, Use & Care Manual

Page: 22 / 60

22 22 22 22 22
3”
3”
Turn gas
Shut-Off valve
to the Off
position
Disconnect and discard old
flexible gas connector and
old transition ducting material.
Replace with new CSA(AGA)
approved flexible gas line
connector and UL approved
transition duct.
Internal
duct
opening
Wall
Check that exhaust
hood damper opens
and closes freely.
Minimum Clearance Other Than Alcove or
Closet Installation
No clearances to combustible surfaces and for air opening
are needed on both sides, nor to the rear of the appliance.
Consideration must be given to provide adequate clearance
for installation and service.
REMOVING LINT FROM WALL EXHAUST OPENING
• Remove and discard existing plastic or metal foil transition
duct and replace with UL listed transition duct.
1. Preparing for installation of new appliance
Styrofoam
Block
Washer
hoses
and parts
Shipping
Bar
24”
Yellow plastic handle
After the machine is in the home,
remove remaining packing mate-
rial/carton from washer. DO
NOT REMOVE SHIPPING ROD
AT THIS TIME. Remove styrofoam
block. Remove the bag contain-
ing the Washer hoses and parts
from tub. Put styrofoam block
back in tub opening to hold tub
in place during the rest of instal-
lation.
TILT THE APPLIANCE SIDEWAYS AND
REMOVE THE FOAM SHIPPING PADS
BY PULLING AT THE SIDES AND
BREAKING THEM AWAY FROM THE
APPLIANCE LEGS. BE SURE TO RE-
MOVE ALL OF THE FOAM PIECES
AROUND THE LEGS.
NEW HOME OR REMODELING F NEW HOME OR REMODELING F
NEW HOME OR REMODELING F NEW HOME OR REMODELING F NEW HOME OR REMODELING FA
A
A A AUCET
UCET
UCET UCET UCETS/DRAIN
S/DRAIN
S/DRAIN S/DRAIN S/DRAIN
ST ST
ST ST STANDPIPE/ELECTRICAL L
ANDPIPE/ELECTRICAL L
ANDPIPE/ELECTRICAL L ANDPIPE/ELECTRICAL L ANDPIPE/ELECTRICAL LOCA
OCA
OCA OCA OCATION
TION
TION TION TION
Right side of
Laundry Center
Locate spigots,
drain standpipe
and electrical plug
in this area
12”
42”
33”
Floor
W W
W W WARNING
ARNING
ARNING ARNING ARNING
NEVER REUSE OLD FLEXIBLE CONNECTORS.
The use of old flexible connectors can cause leaks and per-
sonal injury. Always use new flexible connectors when install-
ing gas appliances.
DISC DISC DISC DISC DISCONNECTING G ONNECTING G ONNECTING G ONNECTING G ONNECTING GAS AS AS AS AS
2 Gas requirements
• Installation must conform to local codes and ordinances, or
in their absence, the NATIONAL FUEL GAS CODE, ANSI
Z223.
• This gas dryer is equipped with a Valve & Burner Assembly
for use only with natural gas. By using conversion kit
WE25M74 for 27" Models, your local service organization
can convert this dryer for use with propane (LP) gas. ALL
CONVERSIONS MUST BE MADE BY PROPERLY TRAINED
AND QUALIFIED PERSONNEL AND IN ACCORDANCE
WITH LOCAL CODES AND ORDINANCE REQUIREMENTS.
• The appliance must be disconnected from the gas supply
piping system during any pressure testing of that system at
a test pressure in excess of 0.5 PSI (3.4 KPa).
• The appliance must be isolated from the gas supply piping
system by closing
the equipment shut-
off valve during any
pressure testing of
the gas supply pip-
ing of test pressure
equal to or less than
0.5 PSI (3.4 KPa).
W W
W W WARNING
ARNING
ARNING ARNING ARNING
Gas Supply Connection
Move appliance close to final
position. Make sure there is at
least a 24" clearance on right
side of it to remove shipping bar.
PULL SHIPPING BAR OUT US-
ING YELLOW PLASTIC HANDLE.
Keep bar so it can be reinstalled
if the appliance is ever moved
again.