background image

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
Safety Tips 

Before opening LP cylinder valve, check the coupling nut 
for tightness. 

      When grill is not in use, turn off all control knobs and LP 

cylinder valve. 
Never move grill while in operation or still hot. 

      Use long-handled barbecue utensils and oven mitts to 

avoid burns and splatters. 

      Maximum load for sideburner and side shelf is 10 lbs. 
   The grease tray must be inserted into grill and emptied 

after each use. Do not remove grease tray until grill has 
completely cooled. 

      Clean grill often, preferably after each cookout. If a bristle 

brush is used to clean any of the grill cooking surfaces, 
ensure no loose bristles remain on cooking surfaces prior 
to grilling. It is not recommended to clean cooking surfaces 
while grill is hot. 

      If you notice grease or other hot material dripping from grill 

onto valve, hose or regulator, turn off gas supply at once. 
Determine the cause, correct it, then clean and inspect 
valve, hose and regulator before continuing. Perform a 
leak test. 

      Keep ventilation openings in cylinder enclosure (grill cart) 

free and clear of debris. 

    Do not store objects or materials inside the grill cart 

enclosure that would block the flow of combustion air to the 
underside of either the control panel or the firebox bowl. 

    The regulator may make a humming or whistling noise 

during operation. This will not affect safety or use of grill. 

      If you have a grill problem see the "Troubleshooting 

Section"

      If the regulator frosts, turn off grill and LP cylinder valve 

immediately. This indicates a problem with the cylinder and 
it should not be used on any product. Return to supplier! 

 

 

 

 

 

 

 

Ignitor Lighting the Grill 
1. Read instructions before lighting your grill. 
2. Open lid during lighting.   
3. Open LP cylinder or natural gas valve.   
4. Push any burner control knob in and turn the knob to the left 

to “HI” position. You will hear a clicking sound from all 
burners. Keep pressing the knob until the burner is lit. 

 

 
 

• Putting out grease fires by closing the lid is not 

possible. Grills are well ventilated for safety reasons. 

• Do not use water on a grease fire. Personal injury may 

result. If a grease fire develops, turn knobs and LP 
cylinder off. 

• Do not leave grill unattended while preheating or 

burning off food residue on HI. If grill has not been 
regularly cleaned, a grease fire can occur that may 
damage the product. 

 

 
 

For Safe Use of Your Grill and to Avoid Serious 
Injury: 

• Do not let children operate or play near grill. 
• Keep grill area clear and free from materials that 

burn. 

• Do not block holes in sides or back of grill. 

• Check burner flames regularly. 
• Use grill only in well-ventilated space. NEVER use in 

enclosed space such as carport, garage, porch, 
covered patio, or under an overhead structure of any 

kind. 

• Do not use charcoal or ceramic briquets in a gas grill. 

(Unless briquets are supplied with your grill.) 

• Use grill at least 3 ft. from any wall or surface. 

Maintain 10 ft. clearance to objects that can catch 
fire, or to sources of ignition such as pilot lights on 

water heaters, live electrical appliances, etc. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

• Apartment Dwellers: 

Check with management to learn the requirements 

and fire codes for using an LP gas grill in your 
apartment complex. If allowed, use outside on the 

ground floor with a three (3) foot clearance from walls 
or rails. Do not use on or under balconies. 

• NEVER attempt to light burner with lid closed. A 

buildup of non-ignited gas inside a closed grill is 

hazardous. 

• Never operate grill with LP cylinder out of correct 

position specified in assembly instructions. 

• Always close LP cylinder valve and remove 

coupling nut before moving LP cylinder from 
specified operation position.

 

Summary of Contents for 148.20125510









































Reviews: