background image

Kelly Jaguar series KLS-N Sinusoidal Brushless PM Motor Controller User

’s Manual 

   

 

  V2.9 

                                                                                                                                         

 

26

 

(6)Brake Rls Time: Brake Release Time, the time of Brake Torque from max to 0, accuracy 0.1s. 
Range: 1~250 
Factory set is 1 
 
(7)BRK_SW Brk %: BRK_SW Braking Percent, the percent of BRK_SW in max braking. Range: 
0~50 
The brake switch regen mode. You have to turn on the brake switch after the throttle is released 
for the regen to occur. 
Factory set is 10 
 
(8)BRK_AD Brk%:It is used to adjust the max regen percentage of brake variable regen mode. 
This regen mode doesn't need brake switch to support any more for KLS controller. 
 
(9)Torque Speed KP: Speed Percent Kp in Torque Mode. Range: 0~10000    Factory set is 3000 
Torque Speed KI: Speed Integral Ki in Torque Mode. Range: 0~500      Factory set is 80 
Speed Err Limit: Speed Error Limit in Torque Mode. Range: 50~4000 Factory set is 1000 
These three parameters are used for PID adjustment. 
If  you  think  the  acceleration  performance  is  very  very  strong,  please  adjust  them  to  a  lower 
value respectively. 
 
(10)Change Dir brake: Value range: Enable and Disable 
It is only useful when you Enable the joystick function. 
If you want to get swift direction changing by using joystick function, you may enable Change 
Dir brake item in user program. 
It will help the motor change the direction of motor quickly after you shift throttle from 0V to 5V,or 
from 5V to 0V. 
Suggestion: factory default is Disable. 
 
(11) 

Compensation Per% 

Tried to increase the current usage during Anti-Slip operation. 
 
(12)IVT BRK MAX and IVT BRK MIN: These two items are only useful when Joystick function is 
enabled in the user program. When you want to use Change Dir Brake to reduce the delay time 
when you shift the direction under joystick operation, there is a RPM limitation to use Change 
Dir Brake function which is only activated when the motor RPM is between IVT BRK MIN and 
IVT BRK MAX. 
Suggestion: factory default is Disable. 
 

(13)Torque Speed Kp:3000  

Torque Speed Ki:80 

Speed Err Limit:1000 

Summary of Contents for MiniKLS7210NV





































Reviews: