background image

 

 

 

(23)Bluetooth function.Required a small Bluetooth converter which needs to be purchased in 
addition from our website.This small converter is only useful for KLS controller. 
(24)Can support three speed function on the latest version. 

Caution! The regen is not a safe function.Usually you may use the mechanical brake.

 

2.2 Features

 

1)  Intelligence with powerful microprocessor. 
2)  Synchronous  rectification,  ultra  low  drop,  fast  SVPWM  and  FOC  to  achieve  very  high 

efficiency. 

3)  Electronic reversing. 
4)  Voltage monitoring on 3 motor phases, bus, and power supply. 
5)  Voltage monitoring on voltage source 12V and 5V. 
6)  Current sense on all 3 motor phases. 
7)  Current control loop. 
8)  Hardware over current protection. 
9)  Hardware over voltage protection. 
10)  Configurable limit for motor current and battery current. 
11)  Low EMC. 
12)  Battery protection: current cutback, warning and shutdown at configurable high and low 

battery voltage. 

13)  Rugged aluminum housing for maximum heat dissipation and harsh environment. 
14)  Rugged high current terminals, and rugged aviation connectors for small signal. 
15)  Thermal protection: current cut back, warning and shutdown on high temperature. 
16)  Controller can do auto_Identification angle for different degrees of hall sensors. 
17)  Configurable high pedal protection: the controller will not work if high throttle is detected at 

power on. 

18)  Current multiplication: Take less current from battery, output more current to motor. 
19)  Easy installation: 3-wire potentiometer will work. 
20)  Standard PC/Laptop computer to do programming.There is one more choice for customers 

to program KLS controller.Standard Tablet with Android OS to do programming.Need a 
Z-TEK USB TO RS232 cable for connecting the controller to App program in Tablet. 

21)  User program provided. Easy to use. No cost to customers. 
22)  Support motors with any number of poles. 
23) Up  to  70,000  electric  RPM  standard.  (Electric  RPM  =  mechanical  RPM  *  motor  pole 

pairs;Motor pole pairs=Motor poles/2). 

24)  KLS-H:Dust and water protected under sealed condition,IP66 
25)  KLS-8080H.The protection rating is IP54. 

Summary of Contents for KLS-H




































Reviews: