background image

Table of contents

5

PRODUCT SAFETY INFORMATION

The user of the machine should understand the contents of this manual before use, service 

and installation of equipment to the tractor and all other relevant measures. Never wear jew-

ellery, loose clothing, ties, scarves, belts, unbuttoned jackets that can get caught in moving 

parts.

Always wear approved clothing that complies with the provisions of accident prevention pur-

poses, such as non-slip shoes, hearing protection, goggles and gloves. Wear a jacket with re-

flective stickers on the equipment used near public roads.

Contact your dealer, health authority or the nearest equivalent authority for information 

about the current safety regulations and special provisions to guarantee the personal security.

Warning! 

Always disengage the PTO shaft, Turn off the tractor engine and apply the parking 

brake before adjustment is performed on the machine.

DANGER!

Never put your hands or feet near the machine without stopping the implement 

and the tractor engine. The rotors may continue to rotate for up to 1 minute 

* Never leave the machine with the tractor engine running. Turn off the engine and apply the 
parking brake when you leave the equipment, even for a short while.
* Never leave the machine uplifted. The hydraulics can lose pressure and cause the implement 
to fall down.
* Make sure that all guards are fitted correctly and cannot come loose.
* The PTO shaft must be protected throughout its length. Make sure to anchor the safety chain 
well.
* Only the operator of the tractor shall be in the vicinity of the machine during work. No one is 
allowed to stand underneath any suspended load.
* Check before driving that no rocks are sticking up on the field, or lying objects or other debris 
that can be thrown out while operating.
* Keep hands, feet and clothing away from rotating parts.
* Lower the implement to the ground, put tractor in park, turn off engine, and remove the key 
from the ignition before performing maintenance, service or other reparation on the machine.
* Remove buildup of grease, oil or debris.
* Do not drive with the mower if large vibrations occur, stop the machine immediately,
check and correct the error before using the machine again.
* Do not climb on the mower!
* When attaching the machine onto the tractor; do not allow anyone to stand between tractor 
and implement while backing up to it.
* Make sure that there is no longer any pressure in the system before disconnecting or con-
necting the hydraulic hoses.
* Disconnect quick couplings, and be sure to protect hydraulic couplings after use so that they 
are not exposed to dirt.

Summary of Contents for 35-VKM195H

























Reviews: