manualshive.com logo in svg

Keithley 8011, Connection Instructions, Page: 9 / 16

Share
Download
Keithley 8011 Connection Instructions Download Page 9

 

Model 8011 Connection Instructions 

 

Specifications are subject to change without notice. 

PA-1032 Rev. A / April 2011 

9 

 

6. Press 

the 

CONFIG 

key. 

7. Press 

the 

SRC 

or 

MEAS 

key (the sense mode can be set from either the V-SOURCE or the V-MEAS menu). 

8.  If you pressed the SRC key, select 

V-SOURCE > SENSE-MODE

. 

9.  If you pressed the MEAS key, select 

V-MEAS > SENSE-MODE

. 

10. Select 

4-WIRE

 to enable remote sense. 

11.  Test the device. 

 
 

Table 2. Connections for two-terminal device test (remote sense) 

Cable end 

Cable 

Cable end 

Model 2651A rear panel 

CA-552-1 (supplied with the Model 2651A) 

Open 

LO of CA-552-1 

Black CA-560-0 

8010-120 blue terminal 4 

HI of CA-552-1 

Red CA-560-2 

8010-120 yellow terminal 6 

Model 2651A rear panel 

CA-557-1 (supplied with the Model 2651A) 

CS-1629-8 

Sense LO of CS-1629-8 

Black CA-567-0 

8010-120 blue terminal 1 

Sense HI of CS-1629-8 

Red CA-567-2 

8010-120 yellow terminal 3 

 

Figure 6. Connections for two-terminal device test (remote sense) 

S LO

G

G
G
G

S HI

2-T

erminal DUT

Plug

8010-317 insulator plug

(insert into 3-pin socket)

HI

HIGH CURRENT TEST SOCKET KIT

8011

RATINGS:

40V MAX.

15A DC MAX.

50A PULSE MAX.

From

Model 2651A

CA-567-0

(black)

CA-560-0

(black)

CA-560-2

(red)

CS-1629-8

CA-552-1

(supplied with

Model 2651A)

CA-557-1

(supplied with

Model 2651A)

CA-567-2

(red)

From

Model 2651A

8010-120 TO-247

Device Test Board

 

 
 
 

Summary of Contents for 8011

















Reviews:

No comments