manualshive.com logo in svg

Keithley 8011, Connection Instructions, Page: 3 / 16

Share
Download
Keithley 8011 Connection Instructions Download Page 3

 

Model 8011 Connection Instructions 

 

Specifications are subject to change without notice. 

PA-1032 Rev. A / April 2011 

3 

 

Assembly instructions 

NOTE

 

If you are customizing the 8010-130 Customizable Test Board, make customizations before assembling 
the Model 8011. 

See Figure 2 below. 

Tools needed 

•

 

Medium Phillips head screwdriver 

•

 

5/16 in. nut driver or socket wrench 

Assembly instructions 

1.  Select the TO-247 Device Test Board (8010-120) or Customizable Test Board (8010-130), as appropriate for 

your application. 

2.  Connect one end of the ground cable to the ground screw at the center of the mounting plate. 

3.  Attach the ground cable with the #6-32 Keps

®

 washer nut. 

4.  Thread the four nylon hex standoffs onto the four threaded posts on the mounting plate. 

5.  Place the 8010-120 or 8010-130 board on the standoffs. 

6.  Thread four of the Phillips flat-head screws through the 8010-120 or 8010-130 board. 

7. Tighten 

the 

screws. 

8.  Attach the other end of the ground cable to protective earth (ground). 

 

WARNING

 

The ground wire must be attached to a known safety earth (ground). Failure to attach the 
ground wire to a known safety earth (ground) may result in electric shock. 

 

Summary of Contents for 8011

















Reviews:

No comments